Onkyo HT-RC360 instruction manual Remote Controller Setup, Lock Setup, Using the Audio Settings

Page 55

Remote Controller Setup

Main menu

Remote Controller Setup

Remote Mode Setup

See “Looking up for Remote Control Code” (page 62).

Lock Setup

With this preference, you can protect your settings by locking the setup menus.

Main menu

Lock Setup

Setup

`Locked

`Unlocked

When “Locked” is selected, the setup menus will be locked and you cannot change any setting.

Using the Audio Settings

You can change various audio settings from the Home menu (page 37).

1

Press RECEIVER followed by HOME.

2

Use q/wand ENTER to select “Audio”, and then

 

use q/w/e/rto make the desired selection.

Note

These settings are not available in either of the following cases:

a pair of headphones is connected.

the “Audio TV Out” setting is set to “On” (page 53).

HDMI Control (RIHD)” is set to “On” (page 52) and you’re listening through your TV speakers.

Tone Control Settings

Bass

`–10dBto 0dB to +10dB in 2 dB steps.

You can boost or cut low-frequency sounds output from the front speakers.

Treble

`–10dBto 0dB to +10dB in 2 dB steps.

You can boost or cut high-frequency sounds output from the front speakers.

You can adjust the bass and treble for the front speakers, except when the Direct, Pure Audio (Chinese models) listening mode is selected.

Operating on the AV receiver

1

Press TONE repeatedly to select either “Bass” or

 

“Treble”.

2

Use + and to adjust.

Note

To bypass the bass and treble tone circuits, select the Direct, Pure Audio (Chinese models) listening mode.

Speaker Levels

Subwoofer Level

`–15dBto 0dB to +12dB in 1 dB steps.

Center Level

`–12dBto 0dB to +12dB in 1 dB steps.

You can adjust the volume of each speaker while listening to an input source.

These temporary adjustments are cancelled when the AV receiver is set to standby. To save the setting you made here, go to “Level Calibration” (page 44) before setting the AV receiver to standby.

Note

You cannot use this function while the AV receiver is muted.

Speakers that are set to “No” or “None” in

“Speaker Configuration” (page 43) cannot be adjusted.

Audyssey

Audyssey

See “Audyssey” in “Source Setup” (page 46).

Dynamic EQ

See “Dynamic EQ” in “Source Setup” (page 46).

Dynamic Volume

See “Dynamic Volume” in “Source Setup” (page 47).

Note

These technologies can be used when all the following conditions are met:

Room Correction and Speaker Setup is completed. Note that “Audyssey” requires the “Audyssey 2EQ Full Calibration” method.

Any listening mode other than Direct or Pure Audio (Chinese models) is selected.

A pair of headphones is not connected.

The setting is stored individually for each input selector.

En

55

Image 55
Contents HT-RC360 Away from the rear panel or wall, creating a flue-like Local regulations when disposing of batteries10 cm 4 at the rear. The rear edge of the shelf or Board above the apparatus shall be set 10 cmPrecautions Aiming the remote controller Supplied AccessoriesMake sure you have the following accessories Installing the batteriesContents Processing FeaturesServices available may vary depending on the region AmplifierPage Front Panel Front & Rear PanelsFor detailed information, see the pages in parentheses DisplayRear Panel Power cordUREMOTE Control jack See Connecting the AV Receiver for connection pages 12 toControlling the AV Receiver Remote ControllerConnecting Your Speakers Connecting the AV ReceiverConnecting the Speaker Cables Speaker Connection Precautions Speaker ConfigurationAttaching the Speaker Cable Labels Bi-amping the Front Speakers Using a Powered SubwooferHdmi cable Connecting AV componentsAbout AV Connections AV Cables and JacksAudio Return Channel ARC function Connecting Components with HdmiJack Components Assignable How to record a video source Connecting Your ComponentsJack/Port Components Assignable Remote Control Connecting Onkyo uComponentsConnecting a Recording Component System On/Auto Power OnPlug the power cord into an AC wall outlet Connecting the AntennasConnecting the Power Cord Be careful not to injure yourself when using thumbtacksAV receiver comes on, the display lights Turning On/Off the AV ReceiverTurning On Turning OffPlaying the Connected Component Controlling Contents of USB or Network DevicesSelecting the Language for the Onscreen Setup Menus PlaybackPlaying an iPod/iPhone via USB Understanding Icons on the DisplayEnter Listening to Internet Radio Playing a USB DeviceRegistering My Favorites*1 Listening to Other Internet RadioTop menu of Internet Radio Remote Playback Windows Media Player 11 SetupWindows Media Player 12 Setup Playing Music Files on a ServerListening to AM/FM Radio Using Remote PlaybackUsing the Tuner Tuning into Radio StationsUsing RDS Chinese models Presetting AM/FM StationsMode Finding Stations by Type PTY Displaying Radio Text RTListening to Traffic News TP Using the Automatic Speaker Setup Using Basic FunctionsMeasurement procedure Use q/wto select a target, and use e/rto change the setting When you’ve finished making the settings, pressWhen prompted, repeat step ` CancelChanging the Speaker Setup Manually Error MessagesSelecting Listening Modes Using the Listening ModesInput Source Following audio formats are supported by the listening modeAbout Listening Modes Explanatory NotesListening Modes Onkyo-Original DSP Listening ModesHeight Resolution AudioDolby Pro Logic Dolby Pro Logic IIzAudyssey DSX *8 Listening Mode Description Input Speaker Source Layout Neo6Using the Sleep Timer Using the Home MenuSetting the Display Brightness VCR/DVR Using the Music OptimizerDisplaying Source Information Changing the Input DisplayAV Recording Using HeadphonesMuting the AV Receiver RecordingExplanatory Notes Advanced SetupOn-screen Setup Menus Common Procedures in Setup MenuHdmi Input ResolutionInput/Output Assign Monitor OutDigital Audio Input Speaker SetupSpeaker Settings Component Video InputFront Powered ZoneSpeaker Impedance Chinese models Speakers Type FrontUnit Speaker DistanceLevel Calibration Double BassMultiplex/Mono Audio AdjustDolby Audyssey Source SetupTheater-Dimensional Audyssey DSXReference Level Dynamic VolumeSync IntelliVolumeName Edit Picture Adjust Audio Selector Charge ModeDTS/DTS-ES/DTS-HD Listening Mode PresetVolume Setup MiscellaneousOSD Setup Tuner Hardware SetupRemote ID Auto Standby Network Firmware UpdateDhcp Lock Setup Remote Controller SetupUsing the Audio Settings Music Optimizer Late Night CinemaFILTERMusic Optimizer Late NightMaking Zone 2 Connections Connecting Your Zone 2 Speakers Directly to the AV receiverConnecting the Zone Speakers to an Additional Amplifier ZoneMuting Zone Adjusting the Volume for ZoneOperating on the remote controller Controlling Zone 2 ComponentsIPod/iPhone Playback via Onkyo Dock Using the Onkyo DockUP-A1 Dock Without the RI Control Controlling Your iPod/iPhoneRI Dock With the RI ControlAvailable buttons Controlling Other Components Preprogrammed Remote Control CodesLooking up for Remote Control Code Entering Remote Control CodesControlling Other Components Remote Control Codes for Onkyo Components Connected via uResetting Remote Mode Buttons Resetting the Remote ControllerSearch SetupButtons Input TV VOL q / w GuidePower TroubleshootingAudio Video Tuner Remote ControllerUP-A1 Dock for iPod/iPhone USB Device Playback RecordingZone Music Server and Internet RadioOthers Component Video OUT Important Note Regarding Video PlaybackConnecting to the Network Network/USB FeaturesNetwork Requirements Remote playback Server RequirementsUSB Device Requirements Server playbackAbout Dlna Supported Audio File FormatsBefore you start Firmware UpdateUpdate procedure Updating the Firmware via NetworkUpdating the Firmware via USB TroubleshootingErrors during an update via network Error Code DescriptionErrors during an update via USB Signal Selection Connection Tips and Video Signal PathVideo Connection Formats OUT Audio Connection FormatsSupported Audio Formats About HdmiAbout Copyright Protection About p-compatible components Using an RIHD-compatible TV, Player, or RecorderOperations that can be performed with Connection Operate with the remote controller How to connect and setupConfirm the connecting and setting Confirm the settingsTuner Section SpecificationsAmplifier Section General Video Section1080p 1080i 720p 480p/576p 480i/576i Component Composite Video Resolution ChartAvailable resolutions 3840 ⋅ 2160 24/25/30 Hz OutputOnkyo Europe Electronics GmbH UK Branch Onkyo Europe Electronics GmbH

HT-RC360 specifications

The Onkyo HT-RC360 is a versatile home theater receiver that has garnered attention for its impressive features and solid performance. Designed to elevate the home entertainment experience, this receiver combines cutting-edge technology with user-friendly functionality.

One of the standout features of the HT-RC360 is its support for high-definition audio formats. It is equipped with Dolby TrueHD and DTS-HD Master Audio decoding, allowing users to enjoy lossless surround sound that delivers a cinema-like experience from the comfort of their own homes. This ensures that every detail of the audio is preserved, making movies, music, and video games come to life with clarity and depth.

The receiver boasts a robust 7.2 channel amplification system, delivering a total power output of 100 watts per channel. This powerful amplification allows the HT-RC360 to drive a variety of speaker configurations, making it suitable for different room sizes and acoustics. Furthermore, the inclusion of Audyssey MultEQ room correction technology allows users to optimize the sound experience based on their specific room conditions. This results in balanced sound that is tailored to the acoustic characteristics of the space.

Connectivity options are abundant with the HT-RC360. It features multiple HDMI inputs and outputs, supporting 3D video and 4K passthrough, which is essential for modern home theater setups. Users can easily connect various devices, including Blu-ray players, gaming consoles, and streaming devices, making it a central hub for all their entertainment needs. Additionally, the receiver comes with analog and digital audio inputs, allowing flexibility in connecting legacy devices.

Another noteworthy characteristic of the Onkyo HT-RC360 is its built-in compatibility with various streaming services. It supports technologies such as Spotify Connect, allowing users to stream their favorite music directly from their smartphones or tablets. This feature enhances the convenience for users who prefer to access music libraries online without the need for physical media.

Overall, the Onkyo HT-RC360 is a remarkable home theater receiver that combines high-quality audio performance with modern connectivity features. Its powerful amplification, advanced audio decoding, and versatile streaming capabilities make it an excellent choice for anyone looking to create an immersive home entertainment experience. With the HT-RC360, users can enjoy movies, music, and gaming like never before.