Onkyo TX-NR5009 Listening Mode Preset, Miscellaneous, Volume Setup, Dts/Dts-Es/Dts-Hd

Note

•This setting cannot be selected when:

–the UP-A1 Dock with docked iPod/iPhone is not connected to the AV receiver, or

–the docked iPod/iPhone model is not supported.

•When the “Charge Mode” setting is set to “On”, or to “Auto” with your iPod/iPhone recharging, the SLEEP indicator is dimly lit in standby mode. In such conditions, the power consumption of the AV receiver slightly increases. With “Auto”, when the iPod/iPhone becomes fully charged, the SLEEP indicator goes off and the power consumption in standby mode is reduced.

Listening Mode Preset

You can assign a default listening mode to each input source that will be selected automatically when you select each input source. For example, you can set the default listening mode to be used with Dolby Digital input signals. You can select other listening modes during playback, but the mode specified here will be resumed once the AV receiver has been set to standby.

1 Use q/wto select the input source that you want to set, and then press ENTER.

The following menu appears.

5.Listening Mode Preset

1.BD/DVD

2.VCR/DVR

3.CBL/SAT

4.GAME

5.PC

6.AUX

2 Use q/wto select the signal format that you want to set, and then use e/rto select a listening mode.

Only listening modes that can be used with each input signal format can be selected (➔ pages 37 to 42). The “Last Valid” option means that the listening mode selected last will be used.

The “Straight Decode” option means that straight decoding listening mode (Dolby Digital, DTS, etc.) is selected.

Note

•If you connect an input component (such as UP-A1 series Dock that seated iPod) to the UNIVERSAL PORT jack, the only listening modes you can assign to the “PORT” selector are specific to analog sound.

•For the TUNER input selector, only “Analog” will be available.

•For the NET or USB input selector, only “Digital” will be available.

■Analog / PCM / Digital

With this setting, you can specify the listening mode used when an analog (CD, TV, LD, VHS, MD, turntable, radio, cassette, cable, satellite, etc.) or PCM digital (CD, DVD, etc.) audio signal is played.

■Mono/Multiplex Source

With this setting, you can specify the listening mode used when a mono digital audio signal is played (DVD,

En etc.).

■2ch Source

With this setting, you can specify the listening mode used when 2-channel (2/0) stereo digital sources, such as Dolby Digital or DTS, are played.

■Dolby D/Dolby D Plus/TrueHD

With this setting, you can specify the listening mode used when Dolby Digital or Dolby Digital Plus format digital audio signals are played (DVD, etc.). Specifies the default listening mode for Dolby TrueHD sources, such as Blu-ray or HD DVD (input via HDMI).

■DTS/DTS-ES/DTS-HD

With this setting, you can specify the listening mode used when DTS or DTS-HD High Resolution format digital audio signals are played (DVD, LD, CD, etc.). Specifies the default listening mode for DTS-HD Master Audio sources, such as Blu-ray or HD DVD (input via HDMI).

■Other Multich Source

Specifies the default listening mode for multichannel PCM sources from HDMI IN such as DVD-Audio, and DSD multichannel sources such as Super Audio CD.

Miscellaneous

Volume Setup

■Volume Display

`Absolute:

Displayed range is Min, 0.5 to 99.5, Max.

`Relative(THX):

Displayed range is –QdB, –81.5dBto +18.0dB. With this setting, you can choose how the volume level is displayed.

The absolute value 82 is equivalent to the relative value 0 dB.

Note

•If the absolute value is set to 82, “82Ref” will appear on the display and the THX indicator will flash.

■Muting Level

`–QdB (fully muted), –50dBto –10dBin 10 dB steps. This setting determines how much the output is muted when the muting function is used (➔ page 45).

■Maximum Volume

`Off, 50 to 99 (Absolute display)

`Off, –32dBto +17dB (Relative display)

With this setting, you can limit the maximum volume. To disable this setting, select “Off”.