Onkyo TX-NR5009 instruction manual Errors during an update via USB

7 Press RECEIVER followed by SETUP on the

	remote controller.
	The setup menu will be displayed on the TV screen.
	The procedures thereafter can also be performed on
	the AV receiver by using its SETUP, arrow and
	ENTER buttons.
8 Select “Hardware Setup” and press ENTER.
9 Select “Firmware Update” and press ENTER.
10	Select “via USB” and press ENTER.
11	Select “Update” and press ENTER.
	The update process will begin.
	During the update process, the on-screen display
	may disappear depending on the updated program.
	When this occurs, you can still view the update
	progress on the front display of the AV receiver. The
	on-screen display will reappear after the update is
	complete, and upon turning the AV receiver off and
	on again.
	Do not turn off the AV receiver and do not remove
	the USB device during the update process.
12	The message “Completed!” appears on the front
	display of the AV receiver, indicating that the
	update has been completed.
	Remove the USB device.
13	Turn off the AV receiver using 8ON/STANDBY
	on the front panel.

Do not use 8RECEIVER on the remote controller. Once turned off, the AV receiver will automatically turn on again.

Congratulations! You now have the latest firmware installed on your Onkyo AV receiver.

Troubleshooting

Case 1:

If “No Update” is displayed on the front display of the AV receiver, it means that the firmware has already been updated. You do not need to do anything further.

Case 2:

If an error occurs, “Error!! *-**” is displayed on the front display of the AV receiver. (Alpha-numeric characters on the front display are denoted by asterisks.) Refer to the following table and take appropriate action.

■Errors during an update via USB

Error Code	Description
*-10,*-20	The USB device was not detected. Make sure
	the USB flash memory or USB cable is
	properly connected to the USB port. If the
	USB storage device has its own power supply,
	use it to power the USB device.
*-14	The firmware file was not found in the root
	folder of the USB device, or the firmware file
	is for another model. Retry and download the
	file on the support page of the web site,
	following the on-site instructions. If the error
	persists, please contact Onkyo Support and
	provide the error code.
Others	Retry the update procedure from the
	beginning. If the error persists, please contact
	Onkyo Support and provide the error code.

Case 3:

If an error occurs during the update process, disconnect then reconnect the AC power cord and try again.

Case 4:

If an error occurs due to a wrong selection of input sources, turn off and on the AV receiver. Then retry the update.

2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN http://www.onkyo.com/

The Americas

18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 800-229-1687, 201-785-2600

Fax: 201-785-2650

Hours: M-F 9am-8pm/Sat-Sun 10am-4pm ET http://www.us.onkyo.com/

Europe

Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY

Tel: +49-8142-4401-0 Fax: +49-8142-4401-555

http://www.eu.onkyo.com/

China, Hong Kong

Unit 1033, 10/F, Star House, No 3, Salisbury Road, Tsim Sha Tsui Kowloon, Hong Kong. Tel: 852-2429-3118 Fax: 852-2428-9039

http://www.onkyochina.com/

Asia, Oceania, Middle East, Africa

Please contact an Onkyo distributor referring to Onkyo SUPPORT site. http://www.intl.onkyo.com/support/local_support/index.html

En

93