Onkyo TX-NR5009 Zone 2/3, Others, Music Server and Internet Radio, USB Device Playback

Zone 2/3

■There’s no sound

Only components connected to analog inputs can be — played in Zone 2/3.

■The Zone 2/3 speakers produce no sound

See “Multi Zone” for the conditions in which	72
Powered Zone 2/3 cannot be used.
To use the Zone 2 speakers, you must set the	51
“Powered Zone 2” setting to “Yes”.
To use the Zone 3 speakers, you must set the	51
“Powered Zone 3” setting to “Yes”.

Others

■ Standby power consumption

In the following cases, the power consumption in	20, 66,
standby mode may reach up to a maximum of	67
45 W (North American)/50 W (Others):

–You are using the Universal Port jack.

–“Network Control” is set to “Enable” in the “Network” setting.

–“HDMI Control(RIHD)” setting is set to “On”. (Depending on the TV status, the AV receiver will enter standby mode as usual.)

–The “HDMI Through” setting is set to other than “Off”.

Music Server and Internet Radio

■Can’t access the server or Internet radio

Check the network connection between the AV	—
receiver and your router or switch.
Make sure that your modem and router are properly	—
connected, and make sure they are both turned on.
Make sure the server is up and running and	100,
compatible with the AV receiver.	102
Check the “Network” settings.	67

■Playback stops while listening to music files on the server

Make sure your server is compatible with the AV	100,
receiver.	102
If you download or copy large files on your	—
computer, playback may be interrupted. Try closing
any unused programs, use a more powerful
computer, or use a dedicated server.
If the server is serving large music files to several	—
networked devices simultaneously, the network may
become overloaded and playback may be
interrupted. Reduce the number of playback devices
on the network, upgrade your network, or use a
switch instead of a hub.

■Can’t connect to the AV receiver from a Web browser

If you’re using DHCP, your router may not always	67
allocate the same IP address to the AV receiver, so if
you find that you can’t connect to a server or Internet
radio station, recheck the AV receiver’s IP address
on the “Network” screen.
Check the “Network” settings.	67

■The sound changes when I connect my headphones

When a pair of headphones is connected, the	—
listening mode is set to Stereo, unless it’s already set
to Stereo, Mono, Direct, or Pure Audio.

■The speaker distance cannot be set as required

In some cases, corrected values suitable for home	—
theater use may be set automatically.

■ The display doesn’t work

The display is turned off when the Pure Audio	—
listening mode is selected.

■How do I change the language of a multiplex source

Use the “Multiplex” setting on the “Audio Adjust” 55 menu to select “Main” or “Sub”.

■ The ufunctions don’t work

To use u, you must make an uconnection and	22
an analog audio connection (RCA) between the
component and AV receiver, even if they are
connected digitally.
While Zone 2 or Zone 3 is selected, the u	22
functions don’t work.

■The functions System Off/Auto Power On and Direct Change don’t work for components connected via u

While Zone 2 or Zone 3 is selected, the u	22
functions don’t work.

USB Device Playback

■Can’t access the music files on a USB device

Make sure the USB device is plugged in properly. —

The AV receiver supports USB devices that support — the USB mass storage device class. However, playback may not be possible with some USB devices even if they conform to the USB mass storage device class.

USB memory devices with security functions cannot — be played.

■When performing “Automatic Speaker Setup”, the measurement fails and the message “Ambient noise is too high.” is displayed.

This can be caused by a malfunction in your speaker — unit. Check if the unit produces normal sounds.

En

89