Nokia DNT2Mi-fp user manual Product code, Product versions

Page 2

DNT2Mi-fp Data Network Terminal User manual

The information in this documentation is subject to change without notice and describes only the product defined in the introduction of this documentation. This documentation is intended for the use of Nokia's customers only for the purposes of the agreement under which the documentation is submitted, and no part of it may be reproduced or transmitted in any form or means without the prior written permission of Nokia. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia welcomes customer comments as part of the process of continuous development and improvement of the documentation.

The information or statements given in this documentation concerning the suitability, capacity, or performance of the mentioned hardware or software products cannot be considered binding but shall be defined in the agreement made between Nokia and the customer. However, Nokia has made all reasonable efforts to ensure that the instructions contained in the documentation are adequate and free of material errors and omissions. Nokia will, if necessary, explain issues which may not be covered by the documentation.

Nokia's liability for any errors in the documentation is limited to the documentary correction of errors. NOKIA WILL NOT BE RESPONSIBLE IN ANY EVENT FOR ERRORS IN THIS DOCUMENTATION OR FOR ANY DAMAGES, INCIDENTAL OR CONSEQUENTIAL (INCLUDING MONETARY LOSSES), that might arise from the use of this documentation or the information in it.

This documentation and the product it describes are considered protected by copyright according to the applicable laws.

NOKIA logo is a registered trademark of Nokia Corporation.

Other product names mentioned in this documentation may be trademarks of their respective companies, and they are mentioned for identification purposes only.

Copyright © Nokia Corporation 2005. All rights reserved.

The following products comply with the protection requirements of the European Union Council Directive 89/336/EEC relating to electromagnetic compatibility (EMC), provided that installed using EMC-compatible installation practices (installation in mechanical housings stated to be EMC-compatible and using cabling material [at least as well shielded] and practices as stated in relevant Nokia user manuals):

Product code

T65690.01

T65690.02

Product versions

DNT2Mi-fp 2w G.704

DNT2Mi-fp 4w G.704

2 (60)

© Nokia Corporation

DN0445814

 

Nokia Proprietary and Confidential

Issue 2-0 en

Image 2
Contents DNT2Mi-fp Data Network Terminal Product code Product versionsContents Page Document Date Comment Product collection and disposal within the European UnionPage About this document Page DNT2Mi-fp Introduction to DNT2Mi-fpPDHLocal Network Exchange BTS Shdsl Front view Power LEDAlarm LED Page Fastener Rear panelWall mounting Pin modular jack, RJ-11 DSL Line Power supplyLine interface Selection of Power Supply option is done by strapping Strapping instruction for Power SupplyExternal AC/DC converter Supply Remote Power Supply default48V DC Supply Removal instruction Remote power feed through line 48VDC Converter Earthing bar Mm2 wire 110/230 V ACSymmetrical G.704/2M interface Terminal interface704/2M Pin modular jack Pin Data interface RJ-45 Page Use of signal 108 when using Mste Management107 HiZ Tx b OUT 108 109 Tx a OUT 103 Rx b 104 DIP Switch LMI Interface type selectionCode Name Connector type Length DIP-switch Q1 management busPage Automatic power-up test CommissioningQ1 transmission speed Q1 6,1,1 ManagementTiming source Q1 address Q1 6,1,2Line interface Q1 6,3,3 Line settingsPower backoff Q1 6,3,6 Port settings Protection settingsMeasurements After the testsPage S65692.01 A0 Serial number 4H0415 MaintenanceGetting general information DNT2Mi-fp Monitoring alarmsDNT2Mi AS Line No incoming signal Code Severity Q1 messageSB 2, Line TestingSB 1, Port Port Interface Line Interface Q1 management Automatic controllPort Interface Line Monitoring a line Checking measurements and statisticsMeasurements via Q1 DNT2Mi-fp statisticsSystem counters Q1 8,3 Statistics values via Q1Information Abbreviation Description And/or ratio Environmental and mechanical Technical specificationsDNT2Mi-fp dimensions Line interface in accordance with ITU-T G.991.2Data interface Data lead timeData lead-time ACL2i to DNT2Mi-fp = 3 to 32 192 kbit/ to 2048 kbit/sPower supply external AC/DC converter DNT2Mi-fp power supplyPower consumption Remote power supply SafetyDC power supply Mean time between failure MtbfPage Line interface settings Factory settingsService settings Data interface settings E1Alarm limits User priviliges Fault displayIdentifications Controls Settings Measurements Statistics GeneralMain Q1 menu structure Identifications menu 2,1 Controls menu Settings menu structure 2,1Settings menu structure 3,1,2 3,1100 3,1,42,1..5 Give filling value 0 orMeasurements menu structure Statistics menu structure 3,1..2,0 10,3 DNT-fp privileges10,1 10,4