Nokia DNT2Mi-fp user manual 3,1..2,0

Page 58

DNT2Mi-fp Data Network Terminal User manual

8,2

Line statistics:

1 Line status

3 Relative values

4 Absolute values

5 Reset statistics

8,2,3

Line stat relative: 1 15 min periods 2 24h periods

8,2,4

Line stat absolute: 1 15 min periods 2 24h periods

3 Since last reset

1)You can choose up to 100 15 min periods or up to 30 24h periods

*) Not in T65690.01

8,2,3,1..2

Give period 0 to 100 (0=curr., 1=last, 2=prev., etc.)

8,2,3,1..2,0

15 min relative statistics:

			P0 xxd xxh xxmin xxs			Line2*)
					Line1	Line2*)
			UATR	(Rx):	xx	xx
			UATR	(Rx):	xx	xx
			ESR	(Rx):	xx	xx
			SESR	(Rx):	xx	xx
			BBER	(Rx):	xx	xx
8,2,4,1..2
8,2,4,1..2
Give period 0 to 100
(0=curr., 1=last, 2=prev., etc.)

8,2,4,3

RX statistics since last reset:

TT: xxd xxh xxmin xxs

Line1 Line2*)

UAT xx xx

ES xx xx

SES xx xx

BBE xx xx

8,3

System counters:

1 CPU reset counter

2 Time since reset

8,3,1

CPU reset counter:

0Display

1Reset counter

8,2,4,1..2,0

15 min absolute RX statistics:

P0 xxd xxh xxmin xxs Line1 Line2*)

UAT xx xx

ES xx xx

SES xx xx

BBE xx xx

Figure 32. Statistics menu structure (continued)

58 (60)	© Nokia Corporation	DN0445814
	Nokia Proprietary and Confidential	Issue 2-0 en

Image 58

Contents DNT2Mi-fp Data Network Terminal Product code Product versionsContents Page Document Date Comment Product collection and disposal within the European UnionPage About this document Page PDHLocal Network Exchange Introduction to DNT2Mi-fpDNT2Mi-fp BTS Shdsl Alarm LED Power LEDFront view Page Wall mounting Rear panelFastener Line interface Power supplyPin modular jack, RJ-11 DSL Line Selection of Power Supply option is done by strapping Strapping instruction for Power Supply48V DC Supply Remote Power Supply defaultExternal AC/DC converter Supply Removal instruction Remote power feed through line 48VDC Converter Earthing bar Mm2 wire 110/230 V AC704/2M Pin modular jack Pin Data interface RJ-45 Terminal interfaceSymmetrical G.704/2M interface Page Use of signal 108 when using Mste ManagementCode Name Connector type Length DIP Switch LMI Interface type selection107 HiZ Tx b OUT 108 109 Tx a OUT 103 Rx b 104 DIP-switch Q1 management busPage Automatic power-up test CommissioningQ1 transmission speed Q1 6,1,1 ManagementTiming source Q1 address Q1 6,1,2Power backoff Q1 6,3,6 Line settingsLine interface Q1 6,3,3 Port settings Protection settingsMeasurements After the testsPage Getting general information MaintenanceS65692.01 A0 Serial number 4H0415 DNT2Mi-fp Monitoring alarmsDNT2Mi AS Line No incoming signal Code Severity Q1 messageSB 1, Port TestingSB 2, Line Port Interface Line Q1 management Automatic controllPort Interface Line Interface Monitoring a line Checking measurements and statisticsMeasurements via Q1 DNT2Mi-fp statisticsInformation Abbreviation Description And/or ratio Statistics values via Q1System counters Q1 8,3 Environmental and mechanical Technical specificationsDNT2Mi-fp dimensions Line interface in accordance with ITU-T G.991.2Data interface Data lead timeData lead-time ACL2i to DNT2Mi-fp = 3 to 32 192 kbit/ to 2048 kbit/sPower consumption DNT2Mi-fp power supplyPower supply external AC/DC converter Remote power supply SafetyDC power supply Mean time between failure MtbfPage Line interface settings Factory settingsService settings Data interface settings E1Alarm limits User priviliges Fault displayIdentifications Controls Settings Measurements Statistics GeneralMain Q1 menu structure Identifications menu 2,1 Controls menu Settings menu structure 2,1Settings menu structure 3,1,2 3,1100 3,1,42,1..5 Give filling value 0 orMeasurements menu structure Statistics menu structure 3,1..2,0 10,3 DNT-fp privileges10,1 10,4