Nokia DNT2Mi-fp user manual Measurements menu structure

Page 56

DNT2Mi-fp Data Network Terminal User manual

7

DNT-fp measurements:

0 Display all

1 Noise margins

2 Rx levels

3 Tx levels

4Attenuations

5Supply voltage

6Temperature

NM = Noise margin At = Attenuation P = Pair

*) Not in T65690.01

7,0

	P	NM	At	Tx	Rx
	#	dB	dB	dBm	dBm
	1:	xx	xx	xx	xx
	2:	xx	xx	xx	xx *)
	2:	xx	xx	xx	xx *)
	Line voltage xxV
	Temperature xxC

	7,1
	Noise margins:
	Pair 1		xx dB
	Pair 1		xx dB
	Pair 2		xx dB *)

7,2

Rx levels:

Pair 1 xx dBm

Pair 2 xx dBm *)

7,3

Tx levels:

Pair 1 xx dBm

Pair 2 xx dBm *)

7,4

Attenuations:

Pair 1	xx dB
Pair 2	xx dB *)

7,5

Supply voltage: xxV

7,6

Temperature: xxC

Figure 30. Measurements menu structure

56 (60)	© Nokia Corporation	DN0445814
	Nokia Proprietary and Confidential	Issue 2-0 en

Image 56

Contents DNT2Mi-fp Data Network Terminal Product code Product versionsContents Page Document Date Comment Product collection and disposal within the European UnionPage About this document Page DNT2Mi-fp Introduction to DNT2Mi-fpPDHLocal Network Exchange BTS Shdsl Front view Power LEDAlarm LED Page Fastener Rear panelWall mounting Pin modular jack, RJ-11 DSL Line Power supplyLine interface Selection of Power Supply option is done by strapping Strapping instruction for Power SupplyExternal AC/DC converter Supply Remote Power Supply default48V DC Supply Removal instruction Remote power feed through line 48VDC Converter Earthing bar Mm2 wire 110/230 V ACSymmetrical G.704/2M interface Terminal interface704/2M Pin modular jack Pin Data interface RJ-45 Page Use of signal 108 when using Mste Management107 HiZ Tx b OUT 108 109 Tx a OUT 103 Rx b 104 DIP Switch LMI Interface type selectionCode Name Connector type Length DIP-switch Q1 management busPage Automatic power-up test CommissioningManagement Timing sourceQ1 transmission speed Q1 6,1,1 Q1 address Q1 6,1,2Line interface Q1 6,3,3 Line settingsPower backoff Q1 6,3,6 Port settings Protection settingsMeasurements After the testsPage S65692.01 A0 Serial number 4H0415 MaintenanceGetting general information Monitoring alarms DNT2Mi AS Line No incoming signalDNT2Mi-fp Code Severity Q1 messageSB 2, Line TestingSB 1, Port Port Interface Line Interface Q1 management Automatic controllPort Interface Line Checking measurements and statistics Measurements via Q1Monitoring a line DNT2Mi-fp statisticsSystem counters Q1 8,3 Statistics values via Q1Information Abbreviation Description And/or ratio Technical specifications DNT2Mi-fp dimensionsEnvironmental and mechanical Line interface in accordance with ITU-T G.991.2Data interface Data lead timeData lead-time ACL2i to DNT2Mi-fp = 3 to 32 192 kbit/ to 2048 kbit/sPower supply external AC/DC converter DNT2Mi-fp power supplyPower consumption Safety DC power supplyRemote power supply Mean time between failure MtbfPage Factory settings Service settingsLine interface settings Data interface settings E1Alarm limits Fault display Identifications Controls Settings Measurements StatisticsUser priviliges GeneralMain Q1 menu structure Identifications menu 2,1 Controls menu Settings menu structure 2,1Settings menu structure 3,1 1003,1,2 3,1,42,1..5 Give filling value 0 orMeasurements menu structure Statistics menu structure 3,1..2,0 DNT-fp privileges 10,110,3 10,4