Nokia DNT2Mi-fp user manual 2,1..5, Give filling value 0 or

Page 55

Q1 menu diagrams

The factory settings are marked within brackets.

6,4

Port settings:

0Display

1Framing format (No frame)

2Sa bits usage

8 BER alarm limit (E-3)

9 BER alarm severity (B-level alarm)

6,4,1

Framing format:

0 Display

1 No frame

2 Basic frame

3 CRC multiframe

4 BF monitoring

5 CRC monitoring

		6,4,2
		Sa bits usage:
		0	Display
		1	Fill Sa4
		2	Fill Sa5
		3	Fill Sa6
		4	Fill Sa7
		5	Fill Sa8
		6,4,8
		BER alarm limit:
		0	Display
		0	Display
		1	E-3
		2	E-6
		6,4,9
		BER alarm severity:
		0	Display
		0	Display
		1	No alarm
		2	A-level alarm
		3	B-level alarm
6,7		4	AS-level alarm

Load factory settings:

Are you sure?

1Cancel

99Yes

6,4,2,1..5

Give filling value: 0 or 1

Figure 29. Settings menu structure (continued)

DN0445814	© Nokia Corporation	55 (60)
Issue 2-0 en	Nokia Proprietary and Confidential

Image 55

Contents DNT2Mi-fp Data Network Terminal Product versions Product codeContents Page Product collection and disposal within the European Union Document Date CommentPage About this document Page PDHLocal Network Exchange Introduction to DNT2Mi-fpDNT2Mi-fp BTS Shdsl Alarm LED Power LEDFront view Page Wall mounting Rear panelFastener Line interface Power supplyPin modular jack, RJ-11 DSL Line Strapping instruction for Power Supply Selection of Power Supply option is done by strapping48V DC Supply Remote Power Supply defaultExternal AC/DC converter Supply Removal instruction Remote power feed through line 48VDC 110/230 V AC Converter Earthing bar Mm2 wire704/2M Pin modular jack Pin Data interface RJ-45 Terminal interfaceSymmetrical G.704/2M interface Page Management Use of signal 108 when using MsteCode Name Connector type Length DIP Switch LMI Interface type selection107 HiZ Tx b OUT 108 109 Tx a OUT 103 Rx b 104 Q1 management bus DIP-switchPage Commissioning Automatic power-up testQ1 address Q1 6,1,2 ManagementTiming source Q1 transmission speed Q1 6,1,1Power backoff Q1 6,3,6 Line settingsLine interface Q1 6,3,3 Protection settings Port settingsAfter the tests MeasurementsPage Getting general information MaintenanceS65692.01 A0 Serial number 4H0415 Code Severity Q1 message Monitoring alarmsDNT2Mi AS Line No incoming signal DNT2Mi-fpSB 1, Port TestingSB 2, Line Port Interface Line Q1 management Automatic controllPort Interface Line Interface DNT2Mi-fp statistics Checking measurements and statisticsMeasurements via Q1 Monitoring a lineInformation Abbreviation Description And/or ratio Statistics values via Q1System counters Q1 8,3 Line interface in accordance with ITU-T G.991.2 Technical specificationsDNT2Mi-fp dimensions Environmental and mechanicalData lead time Data interface= 3 to 32 192 kbit/ to 2048 kbit/s Data lead-time ACL2i to DNT2Mi-fpPower consumption DNT2Mi-fp power supplyPower supply external AC/DC converter Mean time between failure Mtbf SafetyDC power supply Remote power supplyPage Data interface settings E1 Factory settingsService settings Line interface settingsAlarm limits General Fault displayIdentifications Controls Settings Measurements Statistics User priviligesMain Q1 menu structure Identifications menu 2,1 Controls menu 2,1 Settings menu structureSettings menu structure 3,1,4 3,1100 3,1,2Give filling value 0 or 2,1..5Measurements menu structure Statistics menu structure 3,1..2,0 10,4 DNT-fp privileges10,1 10,3