Nokia DNT2Mi-fp user manual Statistics menu structure

Page 57

Q1 menu diagrams

8

DNT-fp statistics:

1 Port statistics

2 Line statistics

3 System counters

99 Reset all statistics

8,1

Port statistics:

3 Relative values

4 Absolute values

5 Reset statistics

8,1,3

Port stat relative: 1 15 min periods 2 24h periods

8,1,4

Port stat absolute: 1 15 min periods 2 24h periods

3 Since last reset

1)You can choose up to 100 15 min periods or up to 30 24h periods

8,1,3,1..2

Give period 0 to 100: 1) (0=curr., 1=last, 2=prev., etc.)

8,1,3,1..2, 0

15 min relative statistics:

P0 xxd xxh xxmin xxs

UATR	(Rx):	xxxxx
ESR	(Rx):	xxxxx
SESR	(Rx):	xxxxx
BBER	(Rx):	xxxxx
UATR	(Tx):	xxxxx
ESR	(Tx):	xxxxx
SESR	(Tx):	xxxxx

8,1,4,1..2

Give period 0 to 100 1) (0=curr., 1=last, 2=prev., etc.)

8,2

8,3

8,1,4,3

Statistics since last reset: TT xxd xxh xxmin xxs

UAT	(Rx):	xx
ES	(Rx):	xx
SES	(Rx):	xx
BBE	(Rx):	xx
UAT	(Tx):	xx
ES	(Tx):	xx
SES	(Tx):	xx

8,1,4,1..2,0

15 min absolute statistics:

P0 xxd xxh xxmin xxs

UAT	(Rx):	xx
ES	(Rx):	xx
SES	(Rx):	xx
BBE	(Rx):	xx
UAT	(Tx):	xx
ES	(Tx):	xx
SES	(Tx):	xx

Figure 31. Statistics menu structure

DN0445814	© Nokia Corporation	57 (60)
Issue 2-0 en	Nokia Proprietary and Confidential

Image 57

Contents DNT2Mi-fp Data Network Terminal Product versions Product codeContents Page Product collection and disposal within the European Union Document Date CommentPage About this document Page Introduction to DNT2Mi-fp PDHLocal Network ExchangeDNT2Mi-fp BTS Shdsl Power LED Alarm LEDFront view Page Rear panel Wall mountingFastener Power supply Line interfacePin modular jack, RJ-11 DSL Line Strapping instruction for Power Supply Selection of Power Supply option is done by strappingRemote Power Supply default 48V DC SupplyExternal AC/DC converter Supply Removal instruction Remote power feed through line 48VDC 110/230 V AC Converter Earthing bar Mm2 wireTerminal interface 704/2M Pin modular jack Pin Data interface RJ-45Symmetrical G.704/2M interface Page Management Use of signal 108 when using MsteDIP Switch LMI Interface type selection Code Name Connector type Length107 HiZ Tx b OUT 108 109 Tx a OUT 103 Rx b 104 Q1 management bus DIP-switchPage Commissioning Automatic power-up testTiming source ManagementQ1 transmission speed Q1 6,1,1 Q1 address Q1 6,1,2Line settings Power backoff Q1 6,3,6Line interface Q1 6,3,3 Protection settings Port settingsAfter the tests MeasurementsPage Maintenance Getting general informationS65692.01 A0 Serial number 4H0415 DNT2Mi AS Line No incoming signal Monitoring alarmsDNT2Mi-fp Code Severity Q1 messageTesting SB 1, PortSB 2, Line Q1 management Automatic controll Port Interface LinePort Interface Line Interface Measurements via Q1 Checking measurements and statisticsMonitoring a line DNT2Mi-fp statisticsStatistics values via Q1 Information Abbreviation Description And/or ratioSystem counters Q1 8,3 DNT2Mi-fp dimensions Technical specificationsEnvironmental and mechanical Line interface in accordance with ITU-T G.991.2Data lead time Data interface= 3 to 32 192 kbit/ to 2048 kbit/s Data lead-time ACL2i to DNT2Mi-fpDNT2Mi-fp power supply Power consumptionPower supply external AC/DC converter DC power supply SafetyRemote power supply Mean time between failure MtbfPage Service settings Factory settingsLine interface settings Data interface settings E1Alarm limits Identifications Controls Settings Measurements Statistics Fault displayUser priviliges GeneralMain Q1 menu structure Identifications menu 2,1 Controls menu 2,1 Settings menu structureSettings menu structure 100 3,13,1,2 3,1,4Give filling value 0 or 2,1..5Measurements menu structure Statistics menu structure 3,1..2,0 10,1 DNT-fp privileges10,3 10,4