Planar C3013T, C3012T user manual PCI Configuration Status and Error Messages, Message Explanation

Page 56

PCI Configuration Status and Error Messages

The following PCI messages are displayed as a group with bus, device, and function information.

Message

Explanation

Floppy Disk Controller Resource Conflict

The floppy disk controller has requested a

 

resource that is already in use.

 

 

NVRAM Checksum Error,

The ESCD data was reinitialized because of an

NVRAM Cleared

NVRAM checksum error. Rerun the ICU.

 

 

NVRAM Cleared By Jumper

The Clear CMOS DIP switch has been moved

 

to the ON position and CMOS RAM has been

 

cleared.

 

 

NVRAM Data Invalid, NVRAM Cleared

Invalid entry in the ESCD.

 

 

Parallel Port Resource Conflict

The parallel port has requested a resource that

 

is already in use.

 

 

PCI Error Log is Full

This message is displayed when more than 15

 

PCI conflict errors are detected. No additional

 

PCI errors can be logged.

 

 

PCI I/O Port Conflict

Two devices requested the same resource,

 

resulting in a conflict.

 

 

PCI IRQ Conflict

Two devices requested the same resource,

 

resulting in a conflict.

 

 

PCI Memory Conflict

Two devices requested the same resource,

 

resulting in a conflict.

 

 

Primary Boot Device Not Found

The designated primary boot device (hard disk

 

drive, diskette drive, or CD-ROM drive) could

 

not be found.

 

 

Primary IDE Controller Resource Conflict

The primary IDE controller has requested a

 

resource that is already in use.

 

 

Primary Input Device Not Found

The designated primary input device (key-

 

board, mouse, or other, if input is redirected)

 

could not be found.

 

 

Secondary IDE Controller Resource Conflict

The secondary IDE controller has requested a

 

resource that is already in use.

 

 

Serial Port 1 Resource Conflict

Serial port 1 has requested a resource that is

 

already in use.

 

 

Serial Port 2 Resource Conflict

Serial port 1 has requested a resource that is

 

already in use.

 

 

Static Device Resource Conflict

A non-plug-and-play ISA card has requested a

 

resource that is already in use.

 

 

Device Resource Conflict

A non-plug-and-play ISA card has requested a

 

resource that is already in use.

 

 

Appendix C: Troubleshooting 45

Image 56
Contents User’s Manual USER’S Manual Integrated Computer with LCD Color DisplayIi Planar Clean Screen PC User’s Manual Federal Communications Commission FCC Requirements Commencement of WarrantyDuration of Warranty Place of Repair or Replacement Limitation of WarrantyInstallation Technical AssistanceTable of Contents Vi Planar Clean Screen PC User’s Manual Vii Reference GuideBefore You Begin What’s in the box?What’s in this manual? What if I’m missing something?Safety Instructions Clean Screen Mounts and AccessoriesFront Panel Connections BottomChapter One The Installation Express SetupWelcome Chapter Two The Clean Screen PCClean Screen Facts Connections Bottom Back Housing InsideChapter Two The Clean Screen PC Chapter Three Hardware Installation and Replacement Removing the Back HousingInstalling an ISA Adapter Card Do not remove the T-Bar or standoffsTo remove an SO Dimm module Installing MemoryTo install a SO Dimm module Removing the existing hard disk Installing the new hard diskReplacing the Hard Disk Drive Replacing the Battery Flash memory. See Chapter Five Bios SetupReplacing the Fuses Mounting the Clean Screen Chapter Four System Setup Connecting the KeyboardConnecting Peripherals Floppy Drive ConnectorPower Supply Power Cord SelectionHeadphones or External Speakers Powering Up the Clean Screen PCSetup F2 Push-Button Volume ControlDriver Overview Front Panel ControlsSetup Screens Chapter Five Bios SetupEntering the Bios Setup Program Main Menu Boot Sequence Sub-Menu Keyboard Features Sub-MenuMemory Cache Sub-Menu Memory Shadow Sub-MenuBoot Sequence Sub-Menu under Main Menu Boot DelayBoot Sequence Setup PromptFloppy Check Summary ScreenAdvanced Menu Bios Extensions Bios Extension Offset in FBDBios Extension Size Destination AddressLPT Mode Integrated Peripherals Sub-MenuLPT Port Diskette ControllerLocal Bus IDE Adapter Touch Panel Base AddressTouch Panel IRQ Power Menu Power SavingsStandby Timeout Suspend TimeoutFixed Disk Timeout Standby Timer Reset EventsKeyboard Standby Break EventsStandby Wakeup Events Exit Menu Appendix C Restore ConditionClear Over Temperature Error Chapter Six Care and Cleaning Maintenance TipsCleaning Tips Approved cleaning solutions includeAppendix a Product Specifications Thermostatic Switch/Temperature Sensor External Serial PortsPrinter Port Floppy Disk Drive PortDescription Pin Environmental SpecificationsNorth America European Appendix B Programming Interface Memory MapAssigned and Available IRQs Range CPU address Region CachedAddress Device DMAsAddress List Anti-Virus Alert Appendix C TroubleshootingTroubleshooting Procedure Boot Failures CausesProblems At Initial System Startup Problems After the System Has Been Running CorrectlyProblems Running New Application Software Problems Operating Add-In BoardsProblems Operating Pcmcia Cards Problems and Suggestions What happens What to doOver Temperature Error and press enter Error and Information Messages Error Message / Beeps ExplanationError Message Explanation PostPCI Configuration Status and Error Messages Message ExplanationResetting the System Cmos Configuration Appendix D Touch Screen optionalAppendix E Technical Support For ServiceFor Further Information and Driver Updates Canada