Planar C3013T, C3012T Chapter Four System Setup, Connecting the Keyboard, Connecting Peripherals

Page 24

Chapter Four: System Setup

Attach the keyboard and all peripherals before you power up the unit. All connections are made at the bottom of the unit. If you have not yet attached the Clean Screen PC to a standard mount- ing bracket, then lay the unit face down before you attach the keyboard and peripherals. Be sure to use a non-abrasive cloth or other material to protect the face plate.

 

Parallel

 

 

Headphone/

ISA 16-bit

Power

Interface

Power

Com A

Speaker Output Jack

Expansion Slot

Switch

or Printer Port

Connection

Port

(32 to 300 Ohms)

(12 card size)

AT Keyboard

Com B

Floppy Drive Connector

Line In

PCMCIA Type III

Microphone

Connection

Port

(custom interface

Jack

Expansion Port

Jack

 

 

for diagnostic or

 

 

 

 

 

service use only)

 

 

 

Figure 15

Connecting the Keyboard

Your Clean Screen can use any AT style keyboard.

Connecting Peripherals

Mouse

The Clean Screen PC uses a serial type mouse. COM A is the default.

Printer

The parallel port can be used for connecting a local printer.

PCMCIA Port

The Clean Screen allows the connection of one Type III PCMCIA Expansion Card or the use of two Type I or Type II PCMCIA Expansion Cards.

Floppy Drive Connector

Please note that this is NOT a standard floppy drive connection. The Clean Screen is not designed for regular use with an external floppy drive. The connector will only allow use of a Planar 3.5" external floppy drive and is intended only for diagnostic and service use. If you need to load drivers for your operating system or other programs, you will need to obtain the correct drive. See What if I’m missing something? in the Before You Begin section.

Chapter Four: System Setup 13

Image 24
Contents User’s Manual USER’S Manual Integrated Computer with LCD Color DisplayIi Planar Clean Screen PC User’s Manual Commencement of Warranty Duration of WarrantyFederal Communications Commission FCC Requirements Place of Repair or Replacement Limitation of WarrantyInstallation Technical AssistanceTable of Contents Vi Planar Clean Screen PC User’s Manual Vii Reference GuideBefore You Begin What’s in the box?What’s in this manual? What if I’m missing something?Safety Instructions Clean Screen Mounts and AccessoriesFront Panel Connections BottomChapter One The Installation Express SetupChapter Two The Clean Screen PC Clean Screen FactsWelcome Connections Bottom Back Housing InsideChapter Two The Clean Screen PC Chapter Three Hardware Installation and Replacement Removing the Back HousingInstalling an ISA Adapter Card Do not remove the T-Bar or standoffsInstalling Memory To install a SO Dimm moduleTo remove an SO Dimm module Installing the new hard disk Replacing the Hard Disk DriveRemoving the existing hard disk Replacing the Battery Flash memory. See Chapter Five Bios SetupReplacing the Fuses Mounting the Clean Screen Chapter Four System Setup Connecting the KeyboardConnecting Peripherals Floppy Drive ConnectorPower Supply Power Cord SelectionHeadphones or External Speakers Powering Up the Clean Screen PCSetup F2 Push-Button Volume ControlDriver Overview Front Panel ControlsChapter Five Bios Setup Entering the Bios Setup ProgramSetup Screens Main Menu Boot Sequence Sub-Menu Keyboard Features Sub-MenuMemory Cache Sub-Menu Memory Shadow Sub-MenuBoot Sequence Sub-Menu under Main Menu Boot DelayBoot Sequence Setup PromptFloppy Check Summary ScreenAdvanced Menu Bios Extensions Bios Extension Offset in FBDBios Extension Size Destination AddressLPT Mode Integrated Peripherals Sub-MenuLPT Port Diskette ControllerTouch Panel Base Address Touch Panel IRQLocal Bus IDE Adapter Power Menu Power SavingsStandby Timeout Suspend TimeoutFixed Disk Timeout Standby Timer Reset EventsKeyboard Standby Break EventsStandby Wakeup Events Exit Menu Restore Condition Clear Over Temperature ErrorAppendix C Chapter Six Care and Cleaning Maintenance TipsCleaning Tips Approved cleaning solutions includeAppendix a Product Specifications Thermostatic Switch/Temperature Sensor External Serial PortsPrinter Port Floppy Disk Drive PortEnvironmental Specifications North America EuropeanDescription Pin Appendix B Programming Interface Memory MapAssigned and Available IRQs Range CPU address Region CachedDMAs Address ListAddress Device Appendix C Troubleshooting Troubleshooting ProcedureAnti-Virus Alert Boot Failures CausesProblems At Initial System Startup Problems After the System Has Been Running CorrectlyProblems Running New Application Software Problems Operating Add-In BoardsProblems Operating Pcmcia Cards Problems and Suggestions What happens What to doOver Temperature Error and press enter Error and Information Messages Error Message / Beeps ExplanationError Message Explanation PostPCI Configuration Status and Error Messages Message ExplanationResetting the System Cmos Configuration Appendix D Touch Screen optionalFor Service For Further Information and Driver UpdatesAppendix E Technical Support Canada