Planar C3013T, C3012T user manual Replacing the Fuses

Page 22

Replacing the Fuses

Fuse (F1) Schurter 001.1014, 10A;	Fuse (F2) Schurter 3402.0012, 2A
or Fuse (F5) Bussman GDA-10A, 10A

Figure 13

Use only the fuses specified below to prevent damage to the Clean Screen.

Fuses: F1 Schurter 001.1014, 10 A

F2 Schurter 3402.0012, 2 A

F5 Bussman GDA-10A, 10 A

1.Remove the back housing as above.

2.Using a small (jeweler type) flat screwdriver, gently pry up on the fuse.

3.To remove an F2 fuse, gently pry the metal bracket at either end and then lift the fuse out.

4.Snap in a new fuse that meets the above specifications.

Technical Note: The F1 fuse used in earlier products has been replaced by the F5. Depending on your product version, you will have either an F1 or an F5, but not both.

Chapter Three: Hardware Installation and Replacement 11

Image 22

Contents User’s Manual USER’S Manual Integrated Computer with LCD Color DisplayIi Planar Clean Screen PC User’s Manual Duration of Warranty Commencement of WarrantyFederal Communications Commission FCC Requirements Installation Place of Repair or ReplacementLimitation of Warranty Technical AssistanceTable of Contents Vi Planar Clean Screen PC User’s Manual Vii Reference GuideWhat’s in this manual? Before You BeginWhat’s in the box? What if I’m missing something?Safety Instructions Clean Screen Mounts and AccessoriesFront Panel Connections BottomChapter One The Installation Express SetupClean Screen Facts Chapter Two The Clean Screen PCWelcome Connections Bottom Back Housing InsideChapter Two The Clean Screen PC Chapter Three Hardware Installation and Replacement Removing the Back HousingInstalling an ISA Adapter Card Do not remove the T-Bar or standoffsTo install a SO Dimm module Installing MemoryTo remove an SO Dimm module Replacing the Hard Disk Drive Installing the new hard diskRemoving the existing hard disk Replacing the Battery Flash memory. See Chapter Five Bios SetupReplacing the Fuses Mounting the Clean Screen Connecting Peripherals Chapter Four System SetupConnecting the Keyboard Floppy Drive ConnectorHeadphones or External Speakers Power SupplyPower Cord Selection Powering Up the Clean Screen PCDriver Overview Setup F2Push-Button Volume Control Front Panel ControlsEntering the Bios Setup Program Chapter Five Bios SetupSetup Screens Main Menu Memory Cache Sub-Menu Boot Sequence Sub-MenuKeyboard Features Sub-Menu Memory Shadow Sub-MenuBoot Sequence Boot Sequence Sub-Menu under Main MenuBoot Delay Setup PromptFloppy Check Summary ScreenAdvanced Menu Bios Extension Size Bios ExtensionsBios Extension Offset in FBD Destination AddressLPT Port LPT ModeIntegrated Peripherals Sub-Menu Diskette ControllerTouch Panel IRQ Touch Panel Base AddressLocal Bus IDE Adapter Standby Timeout Power MenuPower Savings Suspend TimeoutKeyboard Fixed Disk TimeoutStandby Timer Reset Events Standby Break EventsStandby Wakeup Events Exit Menu Clear Over Temperature Error Restore ConditionAppendix C Cleaning Tips Chapter Six Care and CleaningMaintenance Tips Approved cleaning solutions includeAppendix a Product Specifications Printer Port Thermostatic Switch/Temperature SensorExternal Serial Ports Floppy Disk Drive PortNorth America European Environmental SpecificationsDescription Pin Assigned and Available IRQs Appendix B Programming InterfaceMemory Map Range CPU address Region CachedAddress List DMAsAddress Device Troubleshooting Procedure Appendix C TroubleshootingAnti-Virus Alert Boot Failures CausesProblems At Initial System Startup Problems After the System Has Been Running CorrectlyProblems Running New Application Software Problems Operating Add-In BoardsProblems Operating Pcmcia Cards Problems and Suggestions What happens What to doOver Temperature Error and press enter Error and Information Messages Error Message / Beeps ExplanationError Message Explanation PostPCI Configuration Status and Error Messages Message ExplanationResetting the System Cmos Configuration Appendix D Touch Screen optionalFor Further Information and Driver Updates For ServiceAppendix E Technical Support Canada