Onkyo HT-S5300 instruction manual Muting the AV Receiver, Using the Sleep Timer, Using Headphones

Page 23

Muting the AV Receiver

You can temporarily mute the output of the AV receiver.

Press RECEIVER followed by MUTING.

The output is muted and the MUTING indicator flashes on the display.

Tip

•To unmute, press MUTING again or adjust the volume.

•The Mute function is cancelled when the AV receiver is set to Standby.

Using the Sleep Timer

With the sleep timer, you can set the AV receiver to turn off automatically after a specified period.

Press RECEIVER followed by SLEEP repeatedly to select the required sleep time.

The sleep time can be set from 90 to 10 minutes in 10 minute steps.

The SLEEP indicator lights on the display when the sleep timer has been set. The specified sleep time appears on the display for about five seconds, then the previous display reappears.

Tip

•If you need to cancel the sleep timer, press SLEEP repeatedly until the SLEEP indicator goes off.

•To check the time remaining until the AV receiver sleeps, press SLEEP. Note that if you press SLEEP while the sleep time is being displayed, you’ll shorten the sleep time by 10 minutes.

Using Headphones

Connect a pair of stereo headphones with a stan- dard plug (1/4 inch or 6.3 mm) to the PHONES jack.

Note

•Always turn down the volume before connecting your head- phones.

•While the headphones plug is inserted in the PHONES jack, the speakers are turned off. (The Powered Zone 2 speakers are not turned off.)

•When you connect a pair of headphones, the listening mode is set to Stereo, unless it’s already set to Stereo, Mono or Direct.

•Only the Stereo, Direct, and Mono listening modes can be used with headphones.

Changing the Input Display

When you connect an u-capable Onkyo component, you must configure the input display so that ucan work properly.

This setting can be done only from the front panel.

1 Press TV/CD, GAME or VCR/DVR on the front panel so that “TV/CD”, “GAME” or “VCR/DVR” appears on the display.

2 Press and hold down TV/CD, GAME or VCR/DVR (about 3 seconds) to change the input display.

Repeat this step to select “MD”, “CDR”, “DOCK” or “TAPE”.

For the TV/CD input selector, the input display changes in this order:

TV/CD → MD → CDR

→

TAPE

→

DOCK

 

 

 

→

 

 

 

For the GAME input selector, the setting changes in this order:

GAME ↔ DOCK

For the VCR/DVR input selector, the setting changes in this order:

VCR/DVR ↔ DOCK

Note

•DOCK can be selected for the TV/CD, GAME or VCR/DVR input selector, but not at the same time.

•Enter the appropriate remote control code before using the remote controller for the first time (➔ 51).

Selecting Speaker Layout

You can select the priority of the use of front high or sur- round back speakers.

Press RECEIVER followed by SP LAYOUT

repeatedly.

`FrontHigh:

The sound from front high speakers is output by priority.

`SurroundBack:

The sound from surround back speakers is out- put by priority.

Note

•If the Powered Zone 2 is being used (➔ 45), this setting cannot be selected.

•When the listening mode that doesn’t support front high or sur-

round back speakers is used, the setting cannot be selected.

En

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents HT-S5300 Away from the rear panel or wall, creating a flue-like Always consider the environmental issues and follow10 cm 4 at the rear. The rear edge of the shelf or Board above the apparatus shall be set 10 cmPrecautions Speaker Precautions Package Contents Contents Speaker Package HTP-580 FeaturesAV Receiver HT-R580 Front Panel Front & Rear PanelsRear Panel Power cordUREMOTE Control jack DisplaySubwoofer SKW-580 Speaker PackageControlling the tuner Remote ControllerControlling the AV Receiver Return buttonEnjoying Home Theater About Home TheaterSpeaker Connection Precautions Connecting the AV ReceiverConnecting Your Speakers Speaker ConfigurationTo 5/812 to 15 mm Connecting the Speaker CablesScrew-type speaker terminals Strip 1/2 to 5/8 12 to 15 mm Wall Mounting Using the Rubber Stoppers for a More Stable PlatformUsing the Floor Pads for Subwoofer Hdmi cable About AV ConnectionsConnected image with AV components AV Cables and JacksAudio return channel ARC function Connecting Components with HdmiJack Signal Components Assignable How to record the video Connecting External ComponentsRemote Control Using the AUX Input jacks on the front panelConnecting Onkyo uComponents System On/Auto Power OnAssembling the AM loop antenna Connecting AntennaNorth American models Asian models Audio Connection Formats On-screen setup menus are displayed whenWhich Connections Should I Use? Video Connection FormatsTurning Off Turning On/Off the AV ReceiverTurning On Playing the Connected Component Using the Music OptimizerSetting the Display Brightness Basic OperationsChanging the Input Display Using the Sleep TimerUsing Headphones Muting the AV ReceiverListening to the Radio Using the TunerTuning into Radio Stations Listening to the RadioDeleting Presets Presetting FM/AM StationsUsing RDS excluding North American models Selecting PresetsRDS program types PTY Displaying Radio Text RTFinding Stations by Type PTY Listening to Traffic News TPOn your recorder, start recording RecordingAV Recording That you want to recordSelecting Listening Modes Using the Listening ModesListening Mode Buttons Speaker Layout About Listening ModesExplanatory Notes Input SourceListening Modes DTS-HD High Resolution AudioDolby Digital Plus *5 Dolby TrueHDUnplugged Onkyo-Original DSP Listening ModesOn-screen Setup Menus Common Procedures in Setup Menu Advanced SetupSubwoofer Hdmi InputComponent Component Video Input Digital Audio Digital Audio InputCrossover Crossover Frequency Sp Config Speaker ConfigurationFront SurrBack ChSp Distance Speaker Distance Audio AdjustMultiplex/Mono Settings Dolby SettingsAudyssey Settings DTS SettingListening Angle Theater-Dimensional SettingDynamic Volume Reference LevelName Edit Speaker SettingsRemote Control Settings FM/AM Frequency Setup SettingsHdmi Setup Speaker Levels Using the Audio SettingsTone Control Settings Audio Selector Late Night FunctionMusic Optimizer CinemaFILTERSync Digital Input Signal FormatsAdjusting the Bass & Treble SyncZone Connecting ZoneConnecting Your Zone 2 Speakers Directly to the AV receiver Connecting Your Zone 2 Speakers to an Amp in ZoneFront High or ZONE2 L/R speaker ter Setting the Powered Zone Using ZoneControlling Zone 2 from the AV receiver Muting Zones Controlling Zone 2 with the Remote ControllerAdjusting the Volume for Zone Operating with the remote controllerOnkyo Dock Cable Connecting an Onkyo DockControlling iPod Models sold are different depending on the regionUP-A1 Dock Using the Onkyo DockWith the RI Control Controlling Your iPodRI Dock Without the RI ControlAvailable buttons Controlling Other Components Preprogrammed Remote Control CodesEntering Remote Control Codes Remote Control Codes for Onkyo Components Connected via uControlling Other Components Resetting Remote Mode ButtonsResetting the Remote Controller You can reset the remote controller to its default settingsCH + Disc + Cassettetape deckTV VOL q/w There’s no sound, or it’s very quiet TroubleshootingStandby indicator flashes red Can’t turn on the AV receiverOnly the center speaker produces sound There’s no sound with a certain signal formatVolume cannot be set to About DTS signalsOn-screen menus don’t appear Remote controller doesn’t workAV receiver’s remote controller doesn’t control your iPod There’s no picture from a source connected to an HdmiUfunctions don’t work Sound changes when I connect my headphonesCan’t record How do I change the language of a multiplex sourceAV receiver SpecificationsCenter Speaker SKC-580 1ch Home Theater Speaker PackageSubwoofer SKW-580 Front Speaker SKF-580About Copyright Protection About HdmiSupported Audio Formats Operations that can be performed with p connection Using an RIHD-compatible TV, Player, or RecorderAbout p-compatible components Operate with the remote controller How to connect and setupConfirm the connecting and setting Confirm the settingsMemo Onkyo Europe Electronics GmbH UK Branch Onkyo Europe Electronics GmbH

HT-S5300 specifications

The Onkyo HT-S5300 is a home theater system that aims to enhance the cinematic experience in the comfort of your own home. This system is particularly appealing to movie enthusiasts and gamers alike, providing a rich and immersive sound environment that elevates any viewing experience.

At the heart of the HT-S5300 is its 5.1-channel receiver, which is capable of delivering dynamic sound and powerful audio performance. With a total power output of 650 watts, the system can fill a room with vibrant sounds, making it ideal for both quiet movie nights and intense gaming sessions. The receiver includes several advanced audio decoding formats, including Dolby TrueHD and DTS-HD Master Audio, ensuring high-definition audio that is faithful to the original recordings.

One of the standout features of the HT-S5300 is its integrated Audyssey technology. This feature employs sophisticated algorithms that automatically calibrate the audio output based on the unique acoustics of your room. As a result, it provides optimal sound performance, allowing users to enjoy their content with impressive clarity and depth.

The HT-S5300 also includes multiple HDMI inputs, allowing users to connect a variety of devices such as Blu-ray players, gaming consoles, and streaming devices seamlessly. The Audio Return Channel (ARC) ensures that audio from compatible televisions can be sent back to the receiver without needing additional cables, simplifying the setup process.

In addition to digital audio and video capabilities, the HT-S5300 supports wireless streaming through Bluetooth technology. This feature allows users to effortlessly play music from their smartphones, tablets, or other devices directly through the home theater system, broadening the entertainment options available.

The package also includes five compact satellite speakers and a powerful subwoofer, which work together to create a balanced and immersive surround sound environment. The sleek design with a black finish ensures that the speakers can blend seamlessly into any home decor.

Overall, the Onkyo HT-S5300 stands out as a versatile and feature-rich home theater system that combines advanced audio technologies with user-friendly functionality. Whether for movie watching, music listening, or gaming, the HT-S5300 delivers an impressive auditory experience that is sure to satisfy any entertainment enthusiast.
Top Page Image Contents