JVC VR-D0U manual Attaching to the Rack, Connecting the Digital Video Recorder, Preparation

Page 9
Preparation

Preparation

Attaching to the Rack

Use the rack mount fittings provided to attach the unit to the EIA rack.

When installing this unit in the EIA rack, contact your nearest JVC dealer.

Rack mount

fitting

1.Remove the unit side screws.

Remove the front panel side screws (×4).

2.Attach the rack mount fittings.

Use the four screws (M4 × 10 mm) at to fasten both sides of the unit.

3.Remove the feet (×4) from the bottom of the unit.

Loosen the fastening screws and remove them.

4.Attach the unit to the rack.

Use the provided four screws (M5 × 11 mm) at to fasten.

Caution

Never place anything on top of a unit with a rack mount attached. This is to prevent unbalancing the rack, tipping it over, falling, and damaging the unit.

When installing two or more units in a rack, leave space between the units about the size of one unit.

Connecting the Digital Video Recorder

Before connecting the DVR and this unit, make sure that both are switched off.

For more details about the settings and operation of the DVR to be connected to this unit, please refer to the DVR operating instructions.

 

Cable clamp fastener screw

VR-D0U

Cable clamp

 

AC IN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TO RECORDER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Connection cable (provided)

Digital video recorder

 

 

 

 

To the serial terminal

 

 

POWER

1

2

3

4

5

6

7

VIDEO IN 8

9

10

11

12

13

14

15

16

 

ON

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OFF

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

 

 

 

SPOT OUT

 

 

 

 

THROUGH OUT

 

 

 

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

 

2

 

 

 

 

 

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

AC IN 100V

AUDIO IN

AUDIO OUT

VIDEO OUT

VGA OUT

 

LAN

SERIAL

 

RS-232C

 

SIGNAL

ALARM IN

 

 

 

 

 

 

GND

 

 

 

1.Connect this unit and DVR.

Use the provided cable to make the connection.

2.Fasten the connection cable.

Be sure to fasten the cable clamp (this prevents cable disconnection).

Loosen the fastener screw of the cable clamp, then remove the cable clamp.

Pass the connection cable through the cable clamp then fasten it to the unit.

3.Connect the power cord.

Connect the power cord plug to an AC 120 V - 240 V power outlet.

4.Switch this unit on.

5.Switch the DVR on.

6.Do the settings for the DVR.

Do the settings by following the procedures in the DVR operating instructions.

Note

Never switch off the unit while the HDD ACCESS display is lit.

Always make sure that the DVR is switched off before you switch on this power.

Always power off the DVR before you switch off this unit. (The HDD ACCESS display may stay lit for about 30 seconds after the DVR has been turned off. You may turn off the power to the equipment because communication has ended.)

E-5

Image 9
Contents External HDD Unit Please read the following before getting startedFor Customer Use IMPORTANT SAFEGUARDS INFORMATION SAFETY PRECAUTIONS for USA & CanadaAVERTISSEMENT REMARQUEPOWER SYSTEM Connection to the mains supply SAFETY PRECAUTIONSCaution for AC Power Cord IMPORTANT In the United Kingdom Mains Supply AC 230Attention This symbol is only valid in the European Union Information for Users on Disposal of Old EquipmentEuropean Union Business usersContents Main FeaturesHow to Read this Manual Getting StartedHard Disk Drive PRECAUTIONS5 AC IN Power input terminal 1 POWER switchPart Names and Functions Front ViewConnecting the Digital Video Recorder Attaching to the RackPreparation Specifications Consumable PartsOthers SPANNUNGSVERSORGUNG SICHERHEITSVORKEHRUNGENWARNUNG ACHTUNGEinleitung HauptmerkmaleInhaltVorbereitung SonstigesFestplattenlaufwerk VORSICHTSHINWEISE5 Stromeingangsbuchse AC IN Bezeichnungen und Funktionen der Teile7 TO RECORDER DVR-Anschlussbuchse FrontansichtAnschließen des digitalen Befestigung am RackVideorekorders VorbereitungTechnische Daten VerbrauchsteileSonstiges Attention Ce symbole n’est reconnu que dans l’Union européenne PRÈCAUTIONS DE SÈCURITÈUnion européenne Utilisateurs professionnelsCet appareil est une Unité HDD PrincipalesSommaire caractéristiquesPour commencer PréparationDisque dur PRÉCAUTIONSNomenclature et fonctions 1 Interrupteur POWERVue de face Vue de dosConnexion de l’enregistreur vidéo numérique Fixation à un bâtiPréparation RemarqueCaractéristiques techniques Eléments consommablesDivers Información para los usuarios sobre la eliminación de equipos usados PRECAUCIONES DE SEGURIDADUnión Europea EmpresasContenido Principales funcionesIntroducción PreparaciónUnidad de Disco Duro PRECAUCIONESNombres y funciones de los componentes 1 Interruptor POWERVista frontal Vista traseraConexión de la Grabadora Instalación en el bastidorde Vídeo Digital PreparaciónEspecificaciones Piezas consumiblesOtros Unione Europea PRECAUZIONI PER LA SICUREZZAPer gli utenti aziendali Per altre nazioni al di fuori dell’Unione EuropeaIndice Caratteristiche principaliGuida introduttiva PreparazioneUnità Hard Disk PRECAUZIONINome e funzione delle parti 1 Interruttore POWERLato anteriore Lato posterioreCollegamento del Montaggio in rackregistratore video digitale PreparazioneSpecifiche tecniche Materiali di consumoAltro Page 2006 Victor Company of Japan, Limited VR-D0U External HDD Unit