JVC DLA-SH4KNL Connection Using a LAN Cable, Configuring the Network Settings, Connection Example

Page 20

Launch the web browser on the computer

Remove the lens cap

Insert plug into the power outlet on the wall

3

4

5 Turn on the main power of the projector to set to [I]

5

(Supplied)

Power Cord

3

Setup

Connection Using a LAN Cable

You can control this projector using a computer by connecting the projector and computer to the network (LAN).

Connection Example

Router

(DHCP

LAN

WAN

To LAN

Terminal

5 and above) LAN cables.

of PC for this Projector

Windows XP Professional SP2

Windows XP Home Edition SP2

Pentium3 1 GHz or higher

256 MB and above

●Make use of Internet Explorer Ver. 6.0.

●Windows is either registered trademark or trademark of Microsoft Corporation in the United States and/or other countries.

CAUTION:

●The PC specifications above are reference values for the application software to run smoothly, and are not intended to guarantee their operation.

Note that the applications may not run smoothly depending on the condition of use of the respective users even when the system requirements are satisfied.

Configuring the Network Settings

This sections describes the procedures when the IP address is automatically assigned by the DHCP server.

1 Check to ensure that this projector is connected to the DHCP server via a LAN cable

2 Connect the supplied power cord to the

power input terminal of this projector

2

●The [STANDBY/ON], [LAMP], and [WARNING] indicators light up for about 45 seconds, after which the [STANDBY/ON] indicator turns red.

6

20

Image 20

Contents Projector DLA-SH4KINSTRUCTIONS For Customer useMachine Noise Information Germany only Safety PrecautionsAbout the installation place Do not allow any unqualified person to install the unit Do not cut off the main plug from this equipment Safety Precautions Cont’dPower cord EMC Supplement Contents Check the Accessories/ Optional AccessoriesFeatures How to Read this ManualHigh flexible installation User-friendly interface and high operabilityPrecautions During Use Maintenance ProceduresBurning-in of D-ILA Device Viewing Conditions Brightness of RoomNames and Functions of Parts Front/Right SideNames and Functions of Parts Cont’d RearInstallation When using one set of projector When using two sets of projectors side by side When the projector is suspendedInstalling the Projector and Screen Installation Cont’dProjector Installation When shift amount in the right direction is +25 % When shift amount in the left/right direction is 0 % When shift amount in the left direction is -25 % When light passes through the glass of projection boothInstalling the Projector and Screen Cont’d Projecting images by arranging projectors side by sideScreen Size and Projection Distance Approx .29 m Possible Input Signals and Projected Image Connecting Video Signals of the ComputerConnection During Single-Screen Mode Display Connection During Single-Screen Mode Display Connecting Video Signals Computer Cont’d Connection During Two-Screen/Four Screen Mode Display Connection During Two-Screen/Four-Screen Mode Display Connection Example During Two-Screen ModeConnection Using a LAN Cable Configuring the Network SettingsConnection Example PC for this ProjectorClick Aloginb Using the Mail Delivery FeatureEnter ArootB in Login Name Projecting Image Useful Features During Projection Settings Menu Main MenuSetting Value Description Power Latest ErrorSignal Status TemperatureSetting Menu Cont’d Image MenuDisplay Mode Setting MenuSetting Value Description Input Level Setting Value Description Red Convergence MenuShift Lens MenuFocus Option Menu Network Menu Error message sent from this projector Mail MenuSetting Value Description Mail Setting PasswordMail AddressRS-232C Interface Communication SpecificationsCommand Format ON/OFF External control command table Parameters used for the data format Maintenance Cleaning and Replacing the FilterReplacement of Light Source Lamp Routine ServicingTroubleshooting Mode display When Projection has EndedImage is Unusually darkWhat to do when these messages are displayed Message Cause DetailsLamp Time Over Out of RangeIndicators Measures when the warning mode appearsIndicator Description Check MeasureLatest Error Specifications Specifications Cont’d RS-232C Terminal Pin No Signal Operation Signal DirectionDVI-D Terminal Pin No Signal Pin AssignmentDimensional Outline Drawing Top Side Front RearOthers Page DLA-SH4K Projector Projector DLA-SH4KNLINSTRUCTIONS Safety Precautions Do not allow any unqualified person to install the unit For European continent countries AC200 V to 240 EMC Supplement Connection and Installation Network Settings Ultra-high resolution of 40962400 Design is compact and light, and enables stacking Inclined installation Low power consumptionAccessories Accessories Sold SeparatelyPrecautions During Use Lens Mounting Bracket Lens Cap included with the optional lensProjection Lens optional M L When using one set of projector When using two sets of projectors side by side When the projector is suspended Optional projection lensInstalling the Projector and Screen Projector Installation AngleInstalling the Projector Screen Cont’d When light passes through the glass of projection booth Installing the Projector Screen Cont’d GL-MS4015SZG Zoom lens GL-MS4011SG Short focal length lens Possible Input Signals and Projected Image Connection During Single-Screen Mode Display Channel Link Status 20481200 Connection Example During Two-Screen Mode Connection Example During Four-Screen Mode When assigning IP address from the Dhcp server Specifications of PC for Controlling this Projector When assigning a static IP address Turning On the Main Power IP Address Settings IP address setting at the computerAssigning a static IP address Click Aokb on the ALocal Area Connection PropertiesB screenDeselect the check Select AEnableB Cont’d Assigning a static IP address Cont’dAssigning IP Address from the Dhcp Server After connecting, turn on the main powerSet the Adhcp ClientB setting of this projector to Adhcpb Adjust the zoom ratio screen size when zoom lens is in use Hiding the projected image temporarily Setting Menu Cont’d Enable Lamp Enable FAN Enable Projection Sets gamma to Setting Menu Convergence Menu Lens Menu Option Menu Confirm New Mac Address Login PasswordChange Error message sent from this projector Setting Value Description Mail Setting Command Data Format PC Projector Response Data Format Projector PC External control command table Parameters used for the data formatMaintenance Remove dirt that is attached to the vent holes Clean dirt on the cabinet Clean dirt on the lens Troubleshooting Appear Immediately After power is Turned on Screen doesImmediately When Projection has Ended What to do when these messages are displayed Measures when the warning mode appears STANDBY/ON LampLatest Error Signal System Accessories General Optical System Pin Assignment Front Rear Top Side DLA-SH4KNL Projector