JVC DLA-SH4KNL instruction manual Safety Precautions Cont’d, Power cord

Page 4

Getting Started

Safety Precautions (Cont’d)

POWER CONNECTION

The power supply voltage rating of this product is AC110 V – 120 V, AC200 V – 240 V, the power cord attached conforms to the following power supply voltage. Use only the power cord designated by our dealer to ensure Safety and EMC.

When it is used by other power supply voltage, power cable must be changed.

Ensure that the power cable used for the projector is the correct type for the AC outlet in your country. Consult your product dealer.

Power cord

For European continent countries:

AC200 V – 240 V

(3.3 m)

Power cord

Power supply voltage:

AC110 V – 120 V

(3.3 m)

WARNING:

Do not cut off the main plug from this equipment.

If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or adapter or consult your dealer.

If nonetheless the mains plug is cut off, dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the main supply. If a new main plug has to be fitted, then follow the instruction given below.

WARNING:

THIS APPARATUS MUST BE EARTHED.

IMPORTANT:

The wires in the mains lead on this product are colored in accordance with the following cord: Green-and-yellow : Earth

Blue	: Neutral
Brown	: Live

As these colors may not correspond with the colored making identifying the terminals in your plug, proceed as follows:

The wire which is colored green-and-yellow must be connected to the terminal which is marked M with the letter E or the safety earth or colored green or green-and-yellow.

The wire which is colored blue must be connected to the terminal which is marked with the letter N or colored black.

The wire which is colored brown must be connected to the terminal which is marked with the letter L or colored red.

4

Image 4

Contents Projector DLA-SH4KINSTRUCTIONS For Customer useAbout the installation place Safety PrecautionsMachine Noise Information Germany only Do not allow any unqualified person to install the unit Power cord Safety Precautions Cont’dDo not cut off the main plug from this equipment EMC Supplement Contents Check the Accessories/ Optional AccessoriesFeatures How to Read this ManualHigh flexible installation User-friendly interface and high operabilityPrecautions During Use Maintenance ProceduresBurning-in of D-ILA Device Viewing Conditions Brightness of RoomNames and Functions of Parts Front/Right SideNames and Functions of Parts Cont’d RearInstallation When using one set of projector When using two sets of projectors side by side When the projector is suspendedProjector Installation Installation Cont’dInstalling the Projector and Screen When shift amount in the right direction is +25 % When shift amount in the left/right direction is 0 % When shift amount in the left direction is -25 % When light passes through the glass of projection boothInstalling the Projector and Screen Cont’d Projecting images by arranging projectors side by sideScreen Size and Projection Distance Approx .29 mConnection During Single-Screen Mode Display Connecting Video Signals of the Computer Possible Input Signals and Projected Image Connection During Single-Screen Mode Display Connecting Video Signals Computer Cont’d Connection During Two-Screen/Four Screen Mode Display Connection During Two-Screen/Four-Screen Mode Display Connection Example During Two-Screen ModeConnection Using a LAN Cable Configuring the Network SettingsConnection Example PC for this ProjectorEnter ArootB in Login Name Using the Mail Delivery FeatureClick Aloginb Projecting Image Useful Features During Projection Settings Menu Main MenuSetting Value Description Power Latest ErrorSignal Status TemperatureSetting Menu Cont’d Image MenuSetting Value Description Input Level Setting MenuDisplay Mode Setting Value Description Red Convergence MenuFocus Lens MenuShift Option Menu Network Menu Error message sent from this projector Mail MenuSetting Value Description Mail Setting PasswordMail AddressCommand Format Communication SpecificationsRS-232C Interface Parameters used for the data format External control command tableON/OFF Maintenance Cleaning and Replacing the FilterReplacement of Light Source Lamp Routine ServicingTroubleshooting Mode display When Projection has EndedImage is Unusually darkWhat to do when these messages are displayed Message Cause DetailsLamp Time Over Out of RangeIndicators Measures when the warning mode appearsIndicator Description Check MeasureLatest Error Specifications Specifications Cont’d RS-232C Terminal Pin No Signal Operation Signal DirectionDVI-D Terminal Pin No Signal Pin AssignmentDimensional Outline Drawing Top Side Front RearOthers Page DLA-SH4K Projector Projector DLA-SH4KNLINSTRUCTIONS Safety Precautions Do not allow any unqualified person to install the unit For European continent countries AC200 V to 240 EMC Supplement Connection and Installation Network Settings Ultra-high resolution of 40962400 Design is compact and light, and enables stacking Inclined installation Low power consumptionAccessories Accessories Sold SeparatelyPrecautions During Use Projection Lens optional Lens Cap included with the optional lensLens Mounting Bracket M L When using one set of projector When using two sets of projectors side by side When the projector is suspended Optional projection lensInstalling the Projector and Screen Projector Installation AngleInstalling the Projector Screen Cont’d When light passes through the glass of projection booth Installing the Projector Screen Cont’d GL-MS4015SZG Zoom lens GL-MS4011SG Short focal length lens Possible Input Signals and Projected Image Connection During Single-Screen Mode Display Channel Link Status 20481200 Connection Example During Two-Screen Mode Connection Example During Four-Screen Mode When assigning a static IP address Specifications of PC for Controlling this Projector When assigning IP address from the Dhcp server Turning On the Main Power IP Address Settings IP address setting at the computerAssigning a static IP address Click Aokb on the ALocal Area Connection PropertiesB screenDeselect the check Select AEnableB Cont’d Assigning a static IP address Cont’dSet the Adhcp ClientB setting of this projector to Adhcpb After connecting, turn on the main powerAssigning IP Address from the Dhcp Server Adjust the zoom ratio screen size when zoom lens is in use Hiding the projected image temporarily Setting Menu Cont’d Enable Lamp Enable FAN Enable Projection Sets gamma to Setting Menu Convergence Menu Lens Menu Option Menu Change Mac Address Login PasswordConfirm New Error message sent from this projector Setting Value Description Mail Setting Command Data Format PC Projector Response Data Format Projector PC External control command table Parameters used for the data formatMaintenance Clean dirt on the lens Clean dirt on the cabinet Remove dirt that is attached to the vent holes Troubleshooting Immediately When Projection has Ended Immediately After power is Turned on Screen doesAppear What to do when these messages are displayed Measures when the warning mode appears STANDBY/ON LampLatest Error Signal System Accessories General Optical System Pin Assignment Side Top Front Rear DLA-SH4KNL Projector