JVC DLA-SH4KNL instruction manual Installing the Projector, Screen Cont’d

Page 62

Connection and Installation

Installing the Projector

Movable Range of Projected Image

and Screen (Cont’d)

When shift amount in the right direction is +25 %

Install the projector such that the center of the lens is aligned with the 1/4 position from the left edge of the screen.

GL-MS4015SZG Zoom lens

50 %

25 %

50 %

Projected

Image

25 %

Movable

Range

GL-MS4011SG Short focal length lens

When shift amount in the left/right direction is 0 %

15 %

5 %

15 %

Projected

Image

5 %

Movable

Range

Install the projector such that the center of the lens is aligned with the center of the screen.

When shift amount in the left direction is –25 %

Install the projector such that the center of the lens is aligned with the 1/4 position from the right edge of the screen.

NOTE:

●When using the lens shift feature, do not exceed the range (shift amount) as shown above. If the shift amount exceeds the range as shown, shadows will appear on the projected image.

Lens Fixation Mechanism

A screw for securing the lens mechanism is attached in the factory shipment to prevent damage of the equipment during transportation. If the lens does not move horizontally or vertically when you operate AShiftB in the Lens menu, this could be because the screw has not been removed. When this occurs, please consult your authorized dealer.

14

Image 62

Contents Projector DLA-SH4KINSTRUCTIONS For Customer useMachine Noise Information Germany only Safety PrecautionsAbout the installation place Do not allow any unqualified person to install the unit Do not cut off the main plug from this equipment Safety Precautions Cont’dPower cord EMC Supplement Contents Check the Accessories/ Optional AccessoriesHigh flexible installation FeaturesHow to Read this Manual User-friendly interface and high operabilityBurning-in of D-ILA Device Precautions During UseMaintenance Procedures Viewing Conditions Brightness of RoomNames and Functions of Parts Front/Right SideNames and Functions of Parts Cont’d Rear When using two sets of projectors side by side Installation When using one set of projector When the projector is suspendedInstalling the Projector and Screen Installation Cont’dProjector Installation When shift amount in the left direction is -25 % When shift amount in the right direction is +25 % When shift amount in the left/right direction is 0 % When light passes through the glass of projection boothInstalling the Projector and Screen Cont’d Projecting images by arranging projectors side by sideScreen Size and Projection Distance Approx .29 m Possible Input Signals and Projected Image Connecting Video Signals of the ComputerConnection During Single-Screen Mode Display Connection During Single-Screen Mode Display Connecting Video Signals Computer Cont’d Connection During Two-Screen/Four Screen Mode Display Connection During Two-Screen/Four-Screen Mode Display Connection Example During Two-Screen ModeConnection Example Connection Using a LAN CableConfiguring the Network Settings PC for this ProjectorClick Aloginb Using the Mail Delivery FeatureEnter ArootB in Login Name Projecting Image Useful Features During Projection Settings Menu Main MenuSignal Status Setting Value Description PowerLatest Error TemperatureSetting Menu Cont’d Image MenuDisplay Mode Setting MenuSetting Value Description Input Level Setting Value Description Red Convergence MenuShift Lens MenuFocus Option Menu Network Menu Error message sent from this projector Mail MenuMail Setting Value Description Mail SettingPassword AddressRS-232C Interface Communication SpecificationsCommand Format ON/OFF External control command table Parameters used for the data format Maintenance Cleaning and Replacing the FilterReplacement of Light Source Lamp Routine ServicingTroubleshooting Image is Mode displayWhen Projection has Ended Unusually darkLamp Time Over What to do when these messages are displayedMessage Cause Details Out of RangeIndicator Description Indicators Measures when the warning mode appears Check MeasureLatest Error Specifications DVI-D Terminal Pin No Signal Specifications Cont’dRS-232C Terminal Pin No Signal Operation Signal Direction Pin Assignment Side Dimensional Outline Drawing Top Front RearOthers Page DLA-SH4K Projector Projector DLA-SH4KNLINSTRUCTIONS Safety Precautions Do not allow any unqualified person to install the unit For European continent countries AC200 V to 240 EMC Supplement Connection and Installation Network Settings Inclined installation Ultra-high resolution of 40962400 Design is compact and light, and enables stacking Low power consumptionAccessories Accessories Sold SeparatelyPrecautions During Use Lens Mounting Bracket Lens Cap included with the optional lensProjection Lens optional M L When the projector is suspended When using one set of projector When using two sets of projectors side by side Optional projection lensInstalling the Projector and Screen Projector Installation AngleInstalling the Projector Screen Cont’d When light passes through the glass of projection booth Installing the Projector Screen Cont’d GL-MS4015SZG Zoom lens GL-MS4011SG Short focal length lens Possible Input Signals and Projected Image Connection During Single-Screen Mode Display Channel Link Status 20481200 Connection Example During Two-Screen Mode Connection Example During Four-Screen Mode When assigning IP address from the Dhcp server Specifications of PC for Controlling this Projector When assigning a static IP address Turning On the Main Power Assigning a static IP address IP Address Settings IP address setting at the computer Click Aokb on the ALocal Area Connection PropertiesB screenDeselect the check Select AEnableB Cont’d Assigning a static IP address Cont’dAssigning IP Address from the Dhcp Server After connecting, turn on the main powerSet the Adhcp ClientB setting of this projector to Adhcpb Adjust the zoom ratio screen size when zoom lens is in use Hiding the projected image temporarily Setting Menu Cont’d Enable Lamp Enable FAN Enable Projection Sets gamma to Setting Menu Convergence Menu Lens Menu Option Menu Confirm New Mac Address Login PasswordChange Error message sent from this projector Setting Value Description Mail Setting Command Data Format PC Projector Response Data Format Projector PC External control command table Parameters used for the data formatMaintenance Remove dirt that is attached to the vent holes Clean dirt on the cabinet Clean dirt on the lens Troubleshooting Appear Immediately After power is Turned on Screen doesImmediately When Projection has Ended What to do when these messages are displayed Measures when the warning mode appears STANDBY/ON LampLatest Error General Signal System Accessories Optical System Pin Assignment Front Rear Top Side DLA-SH4KNL Projector