JVC DLA-SH4KNL Setting Value Description Power, Latest Error, Signal Status, RateHz, Pixel H

Page 25

Item

Setting Value

Description

Power

ON

For turning the power ON/OFF.

 

OFF

ON : Turns on the power.

 

 

 

 

OFF : Turns off the power.

 

 

NOTE:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The following operating modes of the projector are displayed to the

 

 

 

right of the OFF button.

 

 

 

 

STANDBY

 

: Standby (OFF)

 

 

 

PROJECTION

: Lamp Illuminated (ON)

 

 

 

FAN ENABLE

: FAN Enable (OFFON)

 

 

 

LAMP ENABLE

: LAMP Enable (OFFON)

 

 

 

DEVICE ENABLE

: Elemental Device Enable (OFFON)

 

 

 

COOLING

 

: Cooling (OFF)

 

 

 

EMERGENCY

: Error Occurred (Cooling not performed)

 

 

 

EMERGENCY COOLING : Error Occurred (Cooling performed)

 

 

 

When in the standby mode, clicking the ON button each time

 

 

 

switches the mode in the sequence of STANDBYDEVICE

 

 

 

ENABLELAMP ENABLEFAN ENABLEPROJECTION.

 

 

 

Clicking the OFF button when the power is on switches the projector

 

 

 

to the cooling mode. The power of the projector cannot be turned on

 

 

 

during the cooling process (180 seconds).

 

 

 

 

 

Latest Error

Displays the latest error number. Refer to ALatest ErrorB for information

 

 

 

on the error number and details. (A Page 42)

 

 

 

 

 

Signal Status

 

Displays information on the input signals.

 

DVI

DVI

: Displays the input terminal number.

 

Rate(Hz)

Rate(Hz)

: Displays the vertical frequency.

 

Pixel H

Pixel H

: Displays the horizontal resolution.

 

Pixel V

Pixel V

: Displays the vertical resolution.

 

Link

Link

: Displays the link status of the DVI terminal.

 

 

 

 

 

Temperature

 

Displays the interior temperature of the projector.

 

Temp. 1

Temp. 1

: External Temperature

 

Temp. 2

Temp. 2

: Internal Temperature

 

 

 

 

 

Projector Usage

 

Displays the time interval during which the lamp is in use.

 

Reset

CAUTION:

 

 

 

 

 

 

 

 

Do not click on AResetB unless the lamp is replaced.

25

Image 25
Contents For Customer use Projector DLA-SH4KINSTRUCTIONSAbout the installation place Safety PrecautionsMachine Noise Information Germany only Do not allow any unqualified person to install the unit Power cord Safety Precautions Cont’dDo not cut off the main plug from this equipment EMC Supplement Check the Accessories/ Optional Accessories ContentsHow to Read this Manual FeaturesHigh flexible installation User-friendly interface and high operabilityMaintenance Procedures Precautions During UseBurning-in of D-ILA Device Viewing Conditions Brightness of RoomFront/Right Side Names and Functions of PartsRear Names and Functions of Parts Cont’d When using one set of projector Installation When using two sets of projectors side by side  When the projector is suspendedProjector Installation Installation Cont’dInstalling the Projector and Screen  When shift amount in the left/right direction is 0 %  When shift amount in the right direction is +25 % When shift amount in the left direction is -25 %  When light passes through the glass of projection boothProjecting images by arranging projectors side by side Installing the Projector and Screen Cont’dApprox .29 m Screen Size and Projection DistanceConnection During Single-Screen Mode Display Connecting Video Signals of the Computer Possible Input Signals and Projected Image  Connection During Single-Screen Mode Display Connection During Two-Screen/Four Screen Mode Display Connecting Video Signals Computer Cont’dConnection Example During Two-Screen Mode  Connection During Two-Screen/Four-Screen Mode DisplayConfiguring the Network Settings Connection Using a LAN CableConnection Example PC for this ProjectorEnter ArootB in Login Name Using the Mail Delivery FeatureClick Aloginb Projecting Image Useful Features During Projection Main Menu Settings MenuLatest Error Setting Value Description PowerSignal Status TemperatureImage Menu Setting Menu Cont’dSetting Value Description Input Level Setting MenuDisplay Mode Convergence Menu Setting Value Description RedFocus Lens MenuShift Option Menu Network Menu Mail Menu  Error message sent from this projectorPassword Setting Value Description Mail SettingMail AddressCommand Format Communication SpecificationsRS-232C Interface  Parameters used for the data format  External control command tableON/OFF Cleaning and Replacing the Filter MaintenanceRoutine Servicing Replacement of Light Source LampTroubleshooting When Projection has Ended Mode displayImage is Unusually darkMessage Cause Details What to do when these messages are displayedLamp Time Over Out of Range Measures when the warning mode appears IndicatorsIndicator Description Check MeasureLatest Error Specifications RS-232C Terminal Pin No Signal Operation Signal Direction Specifications Cont’dDVI-D Terminal Pin No Signal  Pin Assignment Top Dimensional Outline Drawing Side  Front  RearOthers Page DLA-SH4K Projector Projector DLA-SH4KNLINSTRUCTIONS Safety Precautions Do not allow any unqualified person to install the unit For European continent countries AC200 V to 240 EMC Supplement Network Settings Connection and Installation Design is compact and light, and enables stacking  Ultra-high resolution of 40962400 Inclined installation  Low power consumptionAccessories Sold Separately AccessoriesPrecautions During Use Projection Lens optional Lens Cap included with the optional lensLens Mounting Bracket M L  When using two sets of projectors side by side  When using one set of projector When the projector is suspended Optional projection lensProjector Installation Angle Installing the Projector and ScreenScreen Cont’d Installing the Projector When light passes through the glass of projection booth  GL-MS4015SZG Zoom lens Installing the Projector Screen Cont’d GL-MS4011SG Short focal length lens  Possible Input Signals and Projected Image  Connection During Single-Screen Mode Display Channel Link Status 20481200  Connection Example During Four-Screen Mode  Connection Example During Two-Screen Mode When assigning a static IP address Specifications of PC for Controlling this Projector When assigning IP address from the Dhcp server Turning On the Main Power  IP address setting at the computer IP Address SettingsAssigning a static IP address Click Aokb on the ALocal Area Connection PropertiesB screenDeselect the check Select AEnableB Assigning a static IP address Cont’d Cont’dSet the Adhcp ClientB setting of this projector to Adhcpb After connecting, turn on the main powerAssigning IP Address from the Dhcp Server Adjust the zoom ratio screen size when zoom lens is in use  Hiding the projected image temporarily Setting Menu Cont’d Enable Lamp Enable FAN Enable Projection Sets gamma to Setting Menu Convergence Menu Lens Menu Option Menu Change Mac Address Login PasswordConfirm New  Error message sent from this projector Setting Value Description Mail Setting  Response Data Format Projector PC  Command Data Format PC Projector Parameters used for the data format  External control command tableMaintenance  Clean dirt on the lens  Clean dirt on the cabinet Remove dirt that is attached to the vent holes Troubleshooting Immediately When Projection has Ended Immediately After power is Turned on Screen doesAppear What to do when these messages are displayed STANDBY/ON Lamp  Measures when the warning mode appearsLatest Error  Accessories  Signal System General  Optical System Pin Assignment  Side  Top Front  Rear DLA-SH4KNL Projector