JVC DLA-SH4KNL instruction manual Turning On the Main Power

Page 71

Turning On the Main

Power

1 Check to ensure that this projector, computer, and switching hub are properly connected 2 Connect the power cord to the power input terminal of this projector

Power Cord

CAUTION:

 

 

(Supplied)

Do not connect the power cord when a lens (optional)

 

is not attached.

2 3

5

3 Insert plug into the power outlet on the wall 4 Remove the lens cap

5 Turn on the main power of the projector to set to [I]

The [STANDBY/ON], [LAMP], and [WARNING] indicators light up for about 45 seconds, after which the [STANDBY/ON] indicator turns red.

NOTE:

The default IP address of all DLA-SH4KNL is “192.168.0.2”. If multiple units of DLA-SH4KNL are used on the same network, do not turn on the main power of more than one projector unit at the same time. Doing so will result in duplication of the IP address, and thereby preventing proper access.

When using multiple units of DLA-SH4KNL, turn on the main power of the second unit and configure accordingly only after configuration of the first unit is complete. Configure subsequent units using the same procedure.

When duplication occurs in the IP address, make sure that only one unit of DLA-SH4KNL is connected on the same network (turn off the main power of the other DLA-SH4KNL units). Allow a time interval of at least 10 minutes before accessing. If access fails, turn off the power of all network equipments on the same network, followed by turning them on again.

23

Image 71
Contents For Customer use Projector DLA-SH4KINSTRUCTIONSMachine Noise Information Germany only Safety PrecautionsAbout the installation place Do not allow any unqualified person to install the unit Do not cut off the main plug from this equipment Safety Precautions Cont’dPower cord EMC Supplement Check the Accessories/ Optional Accessories ContentsUser-friendly interface and high operability FeaturesHow to Read this Manual High flexible installationViewing Conditions Brightness of Room Precautions During UseMaintenance Procedures Burning-in of D-ILA DeviceFront/Right Side Names and Functions of PartsRear Names and Functions of Parts Cont’d When the projector is suspended Installation When using one set of projector  When using two sets of projectors side by sideInstalling the Projector and Screen Installation Cont’dProjector Installation  When light passes through the glass of projection booth  When shift amount in the right direction is +25 % When shift amount in the left/right direction is 0 %  When shift amount in the left direction is -25 %Projecting images by arranging projectors side by side Installing the Projector and Screen Cont’dApprox .29 m Screen Size and Projection Distance Possible Input Signals and Projected Image Connecting Video Signals of the ComputerConnection During Single-Screen Mode Display  Connection During Single-Screen Mode Display Connection During Two-Screen/Four Screen Mode Display Connecting Video Signals Computer Cont’dConnection Example During Two-Screen Mode  Connection During Two-Screen/Four-Screen Mode DisplayPC for this Projector Connection Using a LAN CableConfiguring the Network Settings Connection ExampleClick Aloginb Using the Mail Delivery FeatureEnter ArootB in Login Name Projecting Image Useful Features During Projection Main Menu Settings MenuTemperature Setting Value Description PowerLatest Error Signal StatusImage Menu Setting Menu Cont’dDisplay Mode Setting MenuSetting Value Description Input Level Convergence Menu Setting Value Description RedShift Lens MenuFocus Option Menu Network Menu Mail Menu  Error message sent from this projectorAddress Setting Value Description Mail SettingPassword MailRS-232C Interface Communication SpecificationsCommand Format ON/OFF  External control command table Parameters used for the data format Cleaning and Replacing the Filter MaintenanceRoutine Servicing Replacement of Light Source LampTroubleshooting Unusually dark Mode displayWhen Projection has Ended Image isOut of Range What to do when these messages are displayedMessage Cause Details Lamp Time OverCheck Measure Indicators Measures when the warning mode appears Indicator DescriptionLatest Error Specifications  Pin Assignment Specifications Cont’dRS-232C Terminal Pin No Signal Operation Signal Direction DVI-D Terminal Pin No Signal Front  Rear Dimensional Outline Drawing Top  SideOthers Page DLA-SH4K Projector Projector DLA-SH4KNLINSTRUCTIONS Safety Precautions Do not allow any unqualified person to install the unit For European continent countries AC200 V to 240 EMC Supplement Network Settings Connection and Installation Low power consumption  Ultra-high resolution of 40962400 Design is compact and light, and enables stacking  Inclined installationAccessories Sold Separately AccessoriesPrecautions During Use Lens Mounting Bracket Lens Cap included with the optional lensProjection Lens optional M L Optional projection lens  When using one set of projector When using two sets of projectors side by side  When the projector is suspendedProjector Installation Angle Installing the Projector and ScreenScreen Cont’d Installing the Projector When light passes through the glass of projection booth  GL-MS4015SZG Zoom lens Installing the Projector Screen Cont’d GL-MS4011SG Short focal length lens  Possible Input Signals and Projected Image  Connection During Single-Screen Mode Display Channel Link Status 20481200  Connection Example During Four-Screen Mode  Connection Example During Two-Screen Mode When assigning IP address from the Dhcp server Specifications of PC for Controlling this Projector When assigning a static IP address Turning On the Main Power Click Aokb on the ALocal Area Connection PropertiesB screen IP Address Settings IP address setting at the computer Assigning a static IP addressDeselect the check Select AEnableB Assigning a static IP address Cont’d Cont’dAssigning IP Address from the Dhcp Server After connecting, turn on the main powerSet the Adhcp ClientB setting of this projector to Adhcpb Adjust the zoom ratio screen size when zoom lens is in use  Hiding the projected image temporarily Setting Menu Cont’d Enable Lamp Enable FAN Enable Projection Sets gamma to Setting Menu Convergence Menu Lens Menu Option Menu Confirm New Mac Address Login PasswordChange  Error message sent from this projector Setting Value Description Mail Setting  Response Data Format Projector PC  Command Data Format PC Projector Parameters used for the data format  External control command tableMaintenance  Remove dirt that is attached to the vent holes  Clean dirt on the cabinet Clean dirt on the lens Troubleshooting Appear Immediately After power is Turned on Screen doesImmediately When Projection has Ended What to do when these messages are displayed STANDBY/ON Lamp  Measures when the warning mode appearsLatest Error  Optical System  Signal System Accessories  General Pin Assignment  Front  Rear  Top Side DLA-SH4KNL Projector