JVC DLA-SH4KNL Installation Cont’d, Projector Installation, Installing the Projector and Screen

Page 12

Setup

Installation (Cont’d)

Projector Installation

You can install this projector between 90 .

Images will be properly displayed if the horizontal angle is between the range of 5 .

90

90

5

5

CAUTION:

To ceiling-mount this unit, special expertise and skills are necessary. Make to sure request the authorized dealer or specialized work contractors for installation.

The projector cannot be installed upside down.

Adjusting the Inclination

Adjust the horizontal angle of the projector.

Lift the projector and turn the nut of the adjustable foot with a spanner in the direction indicated by the arrow to extend or retract the foot. The adjustable range is 20 mm.

Extend Retract

Installing the Projector and Screen

It is recommended that this projector be installed at right angle to the screen.

You can shift the projection screen position vertically between 0 % to ±50 %, and horizontally between 0 % to ±25 %. (Lens shift feature)

When shift amount in the upward direction is +50 %

Install the projector such that the lower end of the projection screen is at the same height as the center of the lens.

Screen

90 90 90

Center Line of Lens

When shift amount in the upward/downward direction is 0 %

Install the projector such that the center of the projection screen is at the same height as the center of the lens.

Screen

90 90 90

Center Line of Lens

When shift amount in the downward direction is –50 %

Install the projector such that the upper end of the projection screen is at the same height as the center of the lens.

Screen

 

Center Line of Lens

 

 

90

90

90

12

Image 12
Contents Projector DLA-SH4KINSTRUCTIONS For Customer useSafety Precautions About the installation placeMachine Noise Information Germany only Do not allow any unqualified person to install the unit Safety Precautions Cont’d Power cordDo not cut off the main plug from this equipment EMC Supplement Contents Check the Accessories/ Optional AccessoriesFeatures How to Read this ManualHigh flexible installation User-friendly interface and high operabilityPrecautions During Use Maintenance ProceduresBurning-in of D-ILA Device Viewing Conditions Brightness of RoomNames and Functions of Parts Front/Right SideNames and Functions of Parts Cont’d RearInstallation  When using one set of projector When using two sets of projectors side by side  When the projector is suspendedInstallation Cont’d Projector InstallationInstalling the Projector and Screen  When shift amount in the right direction is +25 %  When shift amount in the left/right direction is 0 % When shift amount in the left direction is -25 %  When light passes through the glass of projection boothInstalling the Projector and Screen Cont’d Projecting images by arranging projectors side by sideScreen Size and Projection Distance Approx .29 mConnecting Video Signals of the Computer Connection During Single-Screen Mode Display Possible Input Signals and Projected Image  Connection During Single-Screen Mode Display Connecting Video Signals Computer Cont’d Connection During Two-Screen/Four Screen Mode Display Connection During Two-Screen/Four-Screen Mode Display Connection Example During Two-Screen ModeConnection Using a LAN Cable Configuring the Network SettingsConnection Example PC for this ProjectorUsing the Mail Delivery Feature Enter ArootB in Login NameClick Aloginb Projecting Image Useful Features During Projection Settings Menu Main MenuSetting Value Description Power Latest ErrorSignal Status TemperatureSetting Menu Cont’d Image MenuSetting Menu Setting Value Description Input LevelDisplay Mode Setting Value Description Red Convergence MenuLens Menu FocusShift Option Menu Network Menu  Error message sent from this projector Mail MenuSetting Value Description Mail Setting PasswordMail AddressCommunication Specifications Command FormatRS-232C Interface  External control command table  Parameters used for the data formatON/OFF Maintenance Cleaning and Replacing the FilterReplacement of Light Source Lamp Routine ServicingTroubleshooting Mode display When Projection has EndedImage is Unusually darkWhat to do when these messages are displayed Message Cause DetailsLamp Time Over Out of RangeIndicators  Measures when the warning mode appearsIndicator Description Check MeasureLatest Error Specifications Specifications Cont’d RS-232C Terminal Pin No Signal Operation Signal DirectionDVI-D Terminal Pin No Signal  Pin AssignmentDimensional Outline Drawing  Top Side  Front  RearOthers Page DLA-SH4K Projector Projector DLA-SH4KNLINSTRUCTIONS Safety Precautions Do not allow any unqualified person to install the unit For European continent countries AC200 V to 240 EMC Supplement Connection and Installation Network Settings Ultra-high resolution of 40962400  Design is compact and light, and enables stacking Inclined installation  Low power consumptionAccessories Accessories Sold SeparatelyPrecautions During Use Lens Cap included with the optional lens Projection Lens optionalLens Mounting Bracket M L  When using one set of projector  When using two sets of projectors side by side When the projector is suspended Optional projection lensInstalling the Projector and Screen Projector Installation AngleInstalling the Projector Screen Cont’d When light passes through the glass of projection booth Installing the Projector Screen Cont’d  GL-MS4015SZG Zoom lens GL-MS4011SG Short focal length lens  Possible Input Signals and Projected Image  Connection During Single-Screen Mode Display Channel Link Status 20481200  Connection Example During Two-Screen Mode  Connection Example During Four-Screen ModeSpecifications of PC for Controlling this Projector  When assigning a static IP address When assigning IP address from the Dhcp server Turning On the Main Power IP Address Settings  IP address setting at the computerAssigning a static IP address Click Aokb on the ALocal Area Connection PropertiesB screenDeselect the check Select AEnableB Cont’d Assigning a static IP address Cont’dAfter connecting, turn on the main power Set the Adhcp ClientB setting of this projector to AdhcpbAssigning IP Address from the Dhcp Server Adjust the zoom ratio screen size when zoom lens is in use  Hiding the projected image temporarily Setting Menu Cont’d Enable Lamp Enable FAN Enable Projection Sets gamma to Setting Menu Convergence Menu Lens Menu Option Menu Mac Address Login Password ChangeConfirm New  Error message sent from this projector Setting Value Description Mail Setting  Command Data Format PC Projector  Response Data Format Projector PC External control command table  Parameters used for the data formatMaintenance  Clean dirt on the cabinet  Clean dirt on the lens Remove dirt that is attached to the vent holes Troubleshooting Immediately After power is Turned on Screen does Immediately When Projection has EndedAppear What to do when these messages are displayed  Measures when the warning mode appears STANDBY/ON LampLatest Error  Signal System  Accessories General  Optical System Pin Assignment  Top  Side Front  Rear DLA-SH4KNL Projector