JVC DLA-SH4KNL instruction manual Assigning IP Address from the Dhcp Server

Page 75

Assigning IP Address from the DHCP Server

The IP address is automatically assigned by the DHCP server.

1 After connecting, turn on the main power.

●Refer to page 22 on the details of connection.

●Refer to page 23 for procedures to turn on the main power.

2 Set the ADHCP ClientB setting of this projector to ADHCPB.

●The AIP Address SettingB of this projector is set to AStatic IPB (the DHCP client function is OFF) by default. When assigning an IP address from the DHCP server, access this projector from the computer to alter the settings. For details on the setting procedures, refer to “Setting (Changing) the IP address of this projector”. (A Page 25)

NOTE:

●Please consult the network administrator on the IP address assigned to this projector.

●When ADHCP ClientB is set to ADHCPB, and if the projector is started up in a LAN where a DHCP server does not exist, the projector will start up using the default IP address instead.

CAUTION:

●Configure the DHCP server such that the same IP address is assigned to the AMac AddressB of this projector by the DHCP server at all times. Connection may fail if the above setting is not performed.

Connecting this projector and the computer using a USB cable

You can connect this projector and the controlling computer using a USB cable.

●You need to install a driver in order to connect the projector and computer using a USB cable.

NOTE:

●For details on the installation of the USB driver, please consult your authorized dealer.

Using the Mail Delivery Feature

This feature enables delivery of mail (error message) to the preset e-mail address when error occurs inside this projector unit.

Connection Example (When DHCP Server is Used)

ADSL modem, etc.

To Internet Connection

ETHER

LAN

WAN		LAN1 LAN2 LAN3 LAN4

DHCP Server

To LAN Terminal

27

Image 75

Contents For Customer use Projector DLA-SH4KINSTRUCTIONSSafety Precautions About the installation placeMachine Noise Information Germany only Do not allow any unqualified person to install the unit Safety Precautions Cont’d Power cordDo not cut off the main plug from this equipment EMC Supplement Check the Accessories/ Optional Accessories ContentsUser-friendly interface and high operability FeaturesHow to Read this Manual High flexible installationViewing Conditions Brightness of Room Precautions During UseMaintenance Procedures Burning-in of D-ILA DeviceFront/Right Side Names and Functions of PartsRear Names and Functions of Parts Cont’d When the projector is suspended Installation When using one set of projector When using two sets of projectors side by sideInstallation Cont’d Projector InstallationInstalling the Projector and Screen When light passes through the glass of projection booth When shift amount in the right direction is +25 % When shift amount in the left/right direction is 0 % When shift amount in the left direction is -25 %Projecting images by arranging projectors side by side Installing the Projector and Screen Cont’dApprox .29 m Screen Size and Projection DistanceConnecting Video Signals of the Computer Connection During Single-Screen Mode Display Possible Input Signals and Projected Image Connection During Single-Screen Mode Display Connection During Two-Screen/Four Screen Mode Display Connecting Video Signals Computer Cont’dConnection Example During Two-Screen Mode Connection During Two-Screen/Four-Screen Mode DisplayPC for this Projector Connection Using a LAN CableConfiguring the Network Settings Connection ExampleUsing the Mail Delivery Feature Enter ArootB in Login NameClick Aloginb Projecting Image Useful Features During Projection Main Menu Settings MenuTemperature Setting Value Description PowerLatest Error Signal StatusImage Menu Setting Menu Cont’dSetting Menu Setting Value Description Input LevelDisplay Mode Convergence Menu Setting Value Description RedLens Menu FocusShift Option Menu Network Menu Mail Menu Error message sent from this projectorAddress Setting Value Description Mail SettingPassword MailCommunication Specifications Command FormatRS-232C Interface External control command table Parameters used for the data formatON/OFF Cleaning and Replacing the Filter MaintenanceRoutine Servicing Replacement of Light Source LampTroubleshooting Unusually dark Mode displayWhen Projection has Ended Image isOut of Range What to do when these messages are displayedMessage Cause Details Lamp Time OverCheck Measure Indicators Measures when the warning mode appears Indicator DescriptionLatest Error Specifications Pin Assignment Specifications Cont’dRS-232C Terminal Pin No Signal Operation Signal Direction DVI-D Terminal Pin No Signal Front Rear Dimensional Outline Drawing Top SideOthers Page DLA-SH4K Projector Projector DLA-SH4KNLINSTRUCTIONS Safety Precautions Do not allow any unqualified person to install the unit For European continent countries AC200 V to 240 EMC Supplement Network Settings Connection and Installation Low power consumption Ultra-high resolution of 40962400 Design is compact and light, and enables stacking Inclined installationAccessories Sold Separately AccessoriesPrecautions During Use Lens Cap included with the optional lens Projection Lens optionalLens Mounting Bracket M L Optional projection lens When using one set of projector When using two sets of projectors side by side When the projector is suspendedProjector Installation Angle Installing the Projector and ScreenScreen Cont’d Installing the Projector When light passes through the glass of projection booth GL-MS4015SZG Zoom lens Installing the Projector Screen Cont’d GL-MS4011SG Short focal length lens Possible Input Signals and Projected Image Connection During Single-Screen Mode Display Channel Link Status 20481200 Connection Example During Four-Screen Mode Connection Example During Two-Screen ModeSpecifications of PC for Controlling this Projector When assigning a static IP address When assigning IP address from the Dhcp server Turning On the Main Power Click Aokb on the ALocal Area Connection PropertiesB screen IP Address Settings IP address setting at the computer Assigning a static IP addressDeselect the check Select AEnableB Assigning a static IP address Cont’d Cont’dAfter connecting, turn on the main power Set the Adhcp ClientB setting of this projector to AdhcpbAssigning IP Address from the Dhcp Server Adjust the zoom ratio screen size when zoom lens is in use Hiding the projected image temporarily Setting Menu Cont’d Enable Lamp Enable FAN Enable Projection Sets gamma to Setting Menu Convergence Menu Lens Menu Option Menu Mac Address Login Password ChangeConfirm New Error message sent from this projector Setting Value Description Mail Setting Response Data Format Projector PC Command Data Format PC Projector Parameters used for the data format External control command tableMaintenance Clean dirt on the cabinet Clean dirt on the lens Remove dirt that is attached to the vent holes Troubleshooting Immediately After power is Turned on Screen does Immediately When Projection has EndedAppear What to do when these messages are displayed STANDBY/ON Lamp Measures when the warning mode appearsLatest Error Optical System Signal System Accessories General Pin Assignment Top Side Front Rear DLA-SH4KNL Projector