Sharp AR-162S operation manual Copier Installation, Do not install your copier in areas that are

Page 10

GETTING STARTED Copier installation

COPIER INSTALLATION

Improper installation may damage the copier. Please note the following during initial installation and whenever the copier is moved.

If the copier is moved from a cool place to a warm place, condensation may form inside the copier. Operation in this condition will cause poor copy quality and malfunctions. Leave the copier at room temperature for at least 2 hours before use.

Do not install your copier in areas that are:

●damp, humid, or very dusty

● exposed to direct sunlight

●poorly ventilated

●subject to extreme temperature or humidity changes, e.g., near an air conditioner or heater.

The copier should be installed near an accessible power outlet for easy connection.

Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements.

Also make certain the outlet is properly grounded.

Connect the copier to a power outlet which is not used for other electric appliances. If a lighting fixture is connected to the same outlet, the light may flicker.

Be sure to allow the required space around the machine for servicing and proper ventilation.

4" (10 cm)

A small amount of ozone is produced within the copier during operation.The emission level is insufficient to cause any health hazard.

NOTE:

The present recommended long term exposure limit for ozone is 0.1 ppm (0.2 mg/m3) calculated as an 8 hr. time-weighted average concentration.

However, since the small amount that is emitted may have an objectionable odor, it is advisable to place the copier in a ventilated area.

8

Image 10

Contents AR-162S Safety Precautions Contents Introduction Conventions used in this manualMain Features Part Names and Functions Part Names and Functions Paper Size indicators Interrupt key and indicator pZoom indicator p.17 Alarm indicatorsOriginal Size Enter key and indicators Start key and indicatorPreset Ratio selector keys and indicators Auto Image key and indicatorCopier Installation Do not install your copier in areas that areDo not touch the photoconductive drum green portion Gently lift and pull out the paper tray until it stops Loading Copy PaperPush the paper tray firmly back into the copier Loading Copy Paper Press the Start key and then the Paper Size Enter key When copying is completed, press the Audit Clear Key Enter your account number using the numeric keysAuditing Accounts Adjust the copy density Turn the power switch onNormal Copying Normal Copying How to remove the platen coverSet the number of copies using the numeric keys Press the Start keyPress the Auto Image key REDUCTION/ENLARGEMENT/ZOOMAutomatic Set the number of copies Press the Start keyManual REDUCTION/ENLARGEMENT/ZOOMSet the number of copies and press the Start key Bypass Feed special paper Unfold the bypass trayBypass Feed special paper TWO-SIDED Copying Press the XY-ZOOM key XY ZoomPress the copy ratio display key Use the Preset Ratio selector , keys and zoom XY ZoomReverse Press the B/W Reverse key Check the copy paper sizeDual page Copy Press the Dual page Copy keyStart key to resume copying Interrupting a Copy RUNPress the Interrupt key Replace the original for the interrupted job and pressAutomatic Exposure Adjustment Toner Save Mode To enter the toner save mode, press the light keyPush the toner cartridge lock release lever and pull Remove the new toner cartridge from the bag. GraspToner cartridge life Toner Cartridge ReplacementPress the light key Misfeed in the copier Misfeed RemovalMisfeed in the bypass tray First confirm the misfeed locationRotating knob in the direction of the arrow to assist Misfeed RemovalCarefully remove the misfed paper. Turn the roller Removing itMisfeed in the transport area Misfeed in the paper tray Close the side cover by pressing the handle on CoverMaintenance Required Developer RequiredList of user programs User ProgramsProgram No Program name Description User Programs Setting the user programsEnter a program number using the numeric keys Program name Program NoSelect the desired parameter using the numeric keys Program name ParametersSelect the desired setting using the numeric keys Settings for auditing accountsEnter a 3-digit account number using the numeric keys Program No Account number change Use the copy ratio display key to select the account Number Press and hold down the 0 keyProgram No Resetting account Preheat mode Power Save ModesAuto power shut-off mode Setting the power save modes Power Save ModesCopying from the preheat mode Original table and platen cover User MaintenanceBypass tray paper feed roller User Maintenance Transfer charger cleaningProblem Solution Copier TROUBLE?Copier TROUBLE? Self-diagnostic function ExampleSupplies Types and sizes of copy paperProper storage SuppliesGenuine supplies statement Store the supplies in a location that isSpecifications Specifications Optional Equipment Single Pass Feeder AR-SP2 SpecificationsPart Names Equipmentoptional Single Pass Feeder AR-SP2 Misfeed removalIndex Index Material Safety Data Sheet Flash Point Method Used Ignition TemperatureSpecial Fire Fighting Procedure Flammable LimitsRoutes of Entry Ingredients CAS No ProportionOther Limits Skin? Ingestion?None required under normal use Memo Memo Page Sharp Corporation

Related manuals

Manual 68 pages 6.94 Kb