Sharp AR-162S operation manual Power Save Modes, Preheat mode, Auto power shut-off mode

Page 44

POWER SAVE MODES

The copier has two power save modes to reduce overall power consumption thereby reduce the cost of operation. In addition, these modes conserve natural resources and help reduce environmental pollution. The two power save modes are preheat mode and auto power shut-off mode.

●User programs

The preheat activation time and the auto power shut-off time have been preset at the factory to 90 sec. for preheat mode and 30 min. for auto power shut-off mode. These times can be changed using user programs. It is suggested that you set appropriate times according to the actual usage of the copier. See page 35.

GENERAL INFORMATION Power save modes

Preheat mode

When the copier enters the preheat mode, the POWER SAVE indicator will light up and other indicators will remain on or off as before. In this condition, the fuser in the copier is maintained at a lower heat level, thereby saving power. The preheat level is, however, high enough to allow the copier to come to a ready condition or begin copying within 10 seconds after any key input or copier operation such as paper tray operation is performed.

Auto power shut-off mode

If the auto power shut-off mode is enabled, the copier will automatically turn off the power once a programmed length of time has elapsed without any copier operation after the last copy of a run is made or the power is first turned on. The power switch will automatically be turned to the “OFF” position. To turn the power back on, simply turn the power switch to the “ON” position.

As an ENERGY STAR® Partner, SHARP has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.

42

Page 43 Page 45
Image 44
Page 43 Page 45
Contents AR-162S Safety Precautions Contents Introduction Conventions used in this manualMain Features Part Names and Functions Part Names and Functions Interrupt key and indicator p Zoom indicator p.17Paper Size indicators Alarm indicatorsStart key and indicator Preset Ratio selector keys and indicatorsOriginal Size Enter key and indicators Auto Image key and indicatorCopier Installation Do not install your copier in areas that areDo not touch the photoconductive drum green portion Push the paper tray firmly back into the copier Loading Copy PaperGently lift and pull out the paper tray until it stops Loading Copy Paper Press the Start key and then the Paper Size Enter key Auditing Accounts Enter your account number using the numeric keysWhen copying is completed, press the Audit Clear Key Normal Copying Turn the power switch onAdjust the copy density How to remove the platen cover Set the number of copies using the numeric keysNormal Copying Press the Start keyREDUCTION/ENLARGEMENT/ZOOM AutomaticPress the Auto Image key Set the number of copies Press the Start keySet the number of copies and press the Start key REDUCTION/ENLARGEMENT/ZOOMManual Bypass Feed special paper Unfold the bypass trayBypass Feed special paper TWO-SIDED Copying Press the copy ratio display key XY ZoomPress the XY-ZOOM key Use the Preset Ratio selector , keys and zoom XY ZoomReverse Press the B/W Reverse key Check the copy paper sizeDual page Copy Press the Dual page Copy keyInterrupting a Copy RUN Press the Interrupt keyStart key to resume copying Replace the original for the interrupted job and pressAutomatic Exposure Adjustment Toner Save Mode To enter the toner save mode, press the light keyPush the toner cartridge lock release lever and pull Remove the new toner cartridge from the bag. GraspPress the light key Toner Cartridge ReplacementToner cartridge life Misfeed Removal Misfeed in the bypass trayMisfeed in the copier First confirm the misfeed locationMisfeed Removal Carefully remove the misfed paper. Turn the rollerRotating knob in the direction of the arrow to assist Removing itMisfeed in the transport area Misfeed in the paper tray Close the side cover by pressing the handle on CoverMaintenance Required Developer RequiredProgram No Program name Description User ProgramsList of user programs Setting the user programs Enter a program number using the numeric keysUser Programs Program name Program NoSelect the desired parameter using the numeric keys Program name ParametersEnter a 3-digit account number using the numeric keys Settings for auditing accountsSelect the desired setting using the numeric keys Program No Account number change Use the copy ratio display key to select the account Number Press and hold down the 0 keyProgram No Resetting account Auto power shut-off mode Power Save ModesPreheat mode Copying from the preheat mode Power Save ModesSetting the power save modes Bypass tray paper feed roller User MaintenanceOriginal table and platen cover User Maintenance Transfer charger cleaningProblem Solution Copier TROUBLE?Copier TROUBLE? Self-diagnostic function ExampleSupplies Types and sizes of copy paperSupplies Genuine supplies statementProper storage Store the supplies in a location that isSpecifications Specifications Optional Equipment Part Names SpecificationsSingle Pass Feeder AR-SP2 Equipmentoptional Single Pass Feeder AR-SP2 Misfeed removalIndex Index Material Safety Data Sheet Ignition Temperature Special Fire Fighting ProcedureFlash Point Method Used Flammable LimitsIngredients CAS No Proportion Other LimitsRoutes of Entry Skin? Ingestion?None required under normal use Memo Memo Page Sharp Corporation
Related manuals
Manual 68 pages 6.94 Kb
Top Page Image Contents