Sharp AR-162S operation manual Push the toner cartridge lock release lever and pull

Page 30

TONER CARTRIDGE REPLACEMENT

When the toner cartridge replacement required ( ) indicator lights up, replacement of the toner cartridge will be needed soon. Obtain a new cartridge. When the toner cartridge replacement required ( ) indicator blinks, the toner cartridge must be replaced before copying can be resumed. Replace the toner cartridge by following the procedure below.

During a long copy run of a dark original, the indicator may blink and the copier stop, even though toner is left.The copier will feed toner up to 2 minutes and then the START key indicator will light up. Press the START key to restart copying.

For best copying results, be sure to use only SHARP Genuine Supplies which are designed, engineered and tested to maximize the life and performance of SHARP copiers. Look for the Genuine Supplies label on the toner package.

STATUSToner cartridge replacement

INDICATORS

Open the bypass tray. Lift slightly on the side cover and

1 slide the cover out until it stops.

2 Push gently on both sides of the front cover and open it.

Toner cartridge lock release lever

Grip

4 or 5 times

Shutter

Tape

Push the toner cartridge lock release lever and pull the

3 toner cartridge out. Remove the toner cartridge while supporting it with the left hand at the green label position.

●For disposal of the old toner cartridge, contact your dealer.

After removing the toner cartridge, do not shake it or tap on it. Doing so may cause toner to leak from the cartridge. Put the old cartridge immediately in the bag contained in the box of the new cartridge.

Remove the new toner cartridge from the bag. Grasp the

4 cartridge on both sides and shake it horizontally four or five times. After shaking the cartridge, remove the tape.

Grasp the grip when holding the cartridge. Do not hold the cartridge by the shutter. Be sure to only shake the cartridge before the tape is removed.

28

Image 30

Contents AR-162S Safety Precautions Contents Introduction Conventions used in this manualMain Features Part Names and Functions Part Names and Functions Paper Size indicators Interrupt key and indicator pZoom indicator p.17 Alarm indicatorsOriginal Size Enter key and indicators Start key and indicatorPreset Ratio selector keys and indicators Auto Image key and indicatorCopier Installation Do not install your copier in areas that areDo not touch the photoconductive drum green portion Loading Copy Paper Gently lift and pull out the paper tray until it stopsPush the paper tray firmly back into the copier Loading Copy Paper Press the Start key and then the Paper Size Enter key Enter your account number using the numeric keys When copying is completed, press the Audit Clear KeyAuditing Accounts Turn the power switch on Adjust the copy densityNormal Copying Normal Copying How to remove the platen coverSet the number of copies using the numeric keys Press the Start keyPress the Auto Image key REDUCTION/ENLARGEMENT/ZOOMAutomatic Set the number of copies Press the Start keyREDUCTION/ENLARGEMENT/ZOOM ManualSet the number of copies and press the Start key Bypass Feed special paper Unfold the bypass trayBypass Feed special paper TWO-SIDED Copying XY Zoom Press the XY-ZOOM keyPress the copy ratio display key Use the Preset Ratio selector , keys and zoom XY ZoomReverse Press the B/W Reverse key Check the copy paper sizeDual page Copy Press the Dual page Copy keyStart key to resume copying Interrupting a Copy RUNPress the Interrupt key Replace the original for the interrupted job and pressAutomatic Exposure Adjustment Toner Save Mode To enter the toner save mode, press the light keyPush the toner cartridge lock release lever and pull Remove the new toner cartridge from the bag. GraspToner Cartridge Replacement Toner cartridge lifePress the light key Misfeed in the copier Misfeed RemovalMisfeed in the bypass tray First confirm the misfeed locationRotating knob in the direction of the arrow to assist Misfeed RemovalCarefully remove the misfed paper. Turn the roller Removing itMisfeed in the transport area Misfeed in the paper tray Close the side cover by pressing the handle on CoverMaintenance Required Developer RequiredUser Programs List of user programsProgram No Program name Description User Programs Setting the user programsEnter a program number using the numeric keys Program name Program NoSelect the desired parameter using the numeric keys Program name ParametersSettings for auditing accounts Select the desired setting using the numeric keysEnter a 3-digit account number using the numeric keys Program No Account number change Use the copy ratio display key to select the account Number Press and hold down the 0 keyProgram No Resetting account Power Save Modes Preheat modeAuto power shut-off mode Power Save Modes Setting the power save modesCopying from the preheat mode User Maintenance Original table and platen coverBypass tray paper feed roller User Maintenance Transfer charger cleaningProblem Solution Copier TROUBLE?Copier TROUBLE? Self-diagnostic function ExampleSupplies Types and sizes of copy paperProper storage SuppliesGenuine supplies statement Store the supplies in a location that isSpecifications Specifications Optional Equipment Specifications Single Pass Feeder AR-SP2Part Names Equipmentoptional Single Pass Feeder AR-SP2 Misfeed removalIndex Index Material Safety Data Sheet Flash Point Method Used Ignition TemperatureSpecial Fire Fighting Procedure Flammable LimitsRoutes of Entry Ingredients CAS No ProportionOther Limits Skin? Ingestion?None required under normal use Memo Memo Page Sharp Corporation

Related manuals

Manual 68 pages 6.94 Kb