Sharp AR-162S operation manual Normal Copying, Turn the power switch on, Adjust the copy density

Page 16

NORMAL COPYING

MAKING COPIES

Normal copying

Power on

1

2

3

4

5

Turn the power switch on.

●It will take about 35 seconds for the copier to warm up. However, you can make desired settings and press the START key during warm-up. Copying will start after warm-up.

●If the copier has been programmed in the auditing mode, the START key indicator will not light up and “–––” will appear in the copy quantity display. Enter an assigned 3-digit account number. See page 13.

●If the power is already on and all indicators except the POWER SAVE indicator are off, the copier is in the auto power shut-off mode. Press the START key in this case. See page 42, POWER SAVE MODES.

Place the original face down on the original table. Align it with the original size scale.

●Image loss (max. 5/32" (4 mm)) can occur at the leading and trailing edges of the copies. Also image loss (max. 5/32" (4 mm) in total) can occur along the other edges of the copies.

Close the platen cover.

Ensure that the copy paper size in the paper tray is the same size as the original.

●If paper of the required size is not loaded in the paper tray, use the bypass tray and press the TRAY SELECT key to select the bypass tray.

Adjust the copy density.

●This copier has three exposure modes to choose from — AUTOMATIC, MANUAL, and PHOTO.

●Automatic exposure is the standard initial setting for this copier. In this mode, the characteristics of the original are “read” by the exposure system and adjustments are automatically made. This optimizes the contrast of the copied images by reducing the effect of colored or shaded background areas. See page 26 to adjust the automatic exposure level.

14

Image 16

Contents AR-162S Safety Precautions Contents Introduction Conventions used in this manualMain Features Part Names and Functions Part Names and Functions Interrupt key and indicator p Zoom indicator p.17Paper Size indicators Alarm indicatorsStart key and indicator Preset Ratio selector keys and indicatorsOriginal Size Enter key and indicators Auto Image key and indicatorCopier Installation Do not install your copier in areas that areDo not touch the photoconductive drum green portion Gently lift and pull out the paper tray until it stops Loading Copy PaperPush the paper tray firmly back into the copier Loading Copy Paper Press the Start key and then the Paper Size Enter key When copying is completed, press the Audit Clear Key Enter your account number using the numeric keysAuditing Accounts Adjust the copy density Turn the power switch onNormal Copying How to remove the platen cover Set the number of copies using the numeric keysNormal Copying Press the Start keyREDUCTION/ENLARGEMENT/ZOOM AutomaticPress the Auto Image key Set the number of copies Press the Start keyManual REDUCTION/ENLARGEMENT/ZOOMSet the number of copies and press the Start key Bypass Feed special paper Unfold the bypass trayBypass Feed special paper TWO-SIDED Copying Press the XY-ZOOM key XY ZoomPress the copy ratio display key Use the Preset Ratio selector , keys and zoom XY ZoomReverse Press the B/W Reverse key Check the copy paper sizeDual page Copy Press the Dual page Copy keyInterrupting a Copy RUN Press the Interrupt keyStart key to resume copying Replace the original for the interrupted job and pressAutomatic Exposure Adjustment Toner Save Mode To enter the toner save mode, press the light keyPush the toner cartridge lock release lever and pull Remove the new toner cartridge from the bag. GraspToner cartridge life Toner Cartridge ReplacementPress the light key Misfeed Removal Misfeed in the bypass trayMisfeed in the copier First confirm the misfeed locationMisfeed Removal Carefully remove the misfed paper. Turn the rollerRotating knob in the direction of the arrow to assist Removing itMisfeed in the transport area Misfeed in the paper tray Close the side cover by pressing the handle on CoverMaintenance Required Developer RequiredList of user programs User ProgramsProgram No Program name Description Setting the user programs Enter a program number using the numeric keysUser Programs Program name Program NoSelect the desired parameter using the numeric keys Program name ParametersSelect the desired setting using the numeric keys Settings for auditing accountsEnter a 3-digit account number using the numeric keys Program No Account number change Use the copy ratio display key to select the account Number Press and hold down the 0 keyProgram No Resetting account Preheat mode Power Save ModesAuto power shut-off mode Setting the power save modes Power Save ModesCopying from the preheat mode Original table and platen cover User MaintenanceBypass tray paper feed roller User Maintenance Transfer charger cleaningProblem Solution Copier TROUBLE?Copier TROUBLE? Self-diagnostic function ExampleSupplies Types and sizes of copy paperSupplies Genuine supplies statementProper storage Store the supplies in a location that isSpecifications Specifications Optional Equipment Single Pass Feeder AR-SP2 SpecificationsPart Names Equipmentoptional Single Pass Feeder AR-SP2 Misfeed removalIndex Index Material Safety Data Sheet Ignition Temperature Special Fire Fighting ProcedureFlash Point Method Used Flammable LimitsIngredients CAS No Proportion Other LimitsRoutes of Entry Skin? Ingestion?None required under normal use Memo Memo Page Sharp Corporation

Related manuals

Manual 68 pages 6.94 Kb