Sharp AR-162S operation manual Automatic Exposure Adjustment

Page 28

AUTOMATIC EXPOSURE ADJUSTMENT

The automatic exposure level can be adjusted to suit your copying needs. This level is set for copying from the original table and copying from the optional SPF respectively. To set the level for the optional SPF, place an original in the document feeder tray and make sure that the SPF indicator lights up before proceeding to step 1. To set the level for the original table, ensure that the SPF indicator does not light up.

MAKING COPIES

Automatic exposure adjustment

1

2

Press the AUTO/MANUAL/PHOTO key to select the PHOTO mode.

Press and hold down the AUTO/MANUAL/PHOTO key for approximately 5 seconds.

●The PHOTO indicator will go out and the AUTO indicator will begin to blink.

●One or two exposure indicators corresponding to the current auto- matic exposure level will light up. The factory default setting is level “3”.

3

4

Press the light () or dark() key to lighten or darken the automatic exposure level as desired.

Press the AUTO/MANUAL/PHOTO key.

●The AUTO indicator will stop blinking and will light up steadily.

●This automatic exposure level will remain in effect until you change it again by this procedure.

26

Image 28

Contents AR-162S Safety Precautions Contents Introduction Conventions used in this manualMain Features Part Names and Functions Part Names and Functions Interrupt key and indicator p Zoom indicator p.17Paper Size indicators Alarm indicatorsStart key and indicator Preset Ratio selector keys and indicatorsOriginal Size Enter key and indicators Auto Image key and indicatorCopier Installation Do not install your copier in areas that areDo not touch the photoconductive drum green portion Gently lift and pull out the paper tray until it stops Loading Copy PaperPush the paper tray firmly back into the copier Loading Copy Paper Press the Start key and then the Paper Size Enter key When copying is completed, press the Audit Clear Key Enter your account number using the numeric keysAuditing Accounts Adjust the copy density Turn the power switch onNormal Copying How to remove the platen cover Set the number of copies using the numeric keysNormal Copying Press the Start keyREDUCTION/ENLARGEMENT/ZOOM AutomaticPress the Auto Image key Set the number of copies Press the Start keyManual REDUCTION/ENLARGEMENT/ZOOMSet the number of copies and press the Start key Bypass Feed special paper Unfold the bypass trayBypass Feed special paper TWO-SIDED Copying Press the XY-ZOOM key XY ZoomPress the copy ratio display key Use the Preset Ratio selector , keys and zoom XY ZoomReverse Press the B/W Reverse key Check the copy paper sizeDual page Copy Press the Dual page Copy keyInterrupting a Copy RUN Press the Interrupt keyStart key to resume copying Replace the original for the interrupted job and pressAutomatic Exposure Adjustment Toner Save Mode To enter the toner save mode, press the light keyPush the toner cartridge lock release lever and pull Remove the new toner cartridge from the bag. GraspToner cartridge life Toner Cartridge ReplacementPress the light key Misfeed Removal Misfeed in the bypass trayMisfeed in the copier First confirm the misfeed locationMisfeed Removal Carefully remove the misfed paper. Turn the rollerRotating knob in the direction of the arrow to assist Removing itMisfeed in the transport area Misfeed in the paper tray Close the side cover by pressing the handle on CoverMaintenance Required Developer RequiredList of user programs User ProgramsProgram No Program name Description Setting the user programs Enter a program number using the numeric keysUser Programs Program name Program NoSelect the desired parameter using the numeric keys Program name ParametersSelect the desired setting using the numeric keys Settings for auditing accountsEnter a 3-digit account number using the numeric keys Program No Account number change Use the copy ratio display key to select the account Number Press and hold down the 0 keyProgram No Resetting account Preheat mode Power Save ModesAuto power shut-off mode Setting the power save modes Power Save ModesCopying from the preheat mode Original table and platen cover User MaintenanceBypass tray paper feed roller User Maintenance Transfer charger cleaningProblem Solution Copier TROUBLE?Copier TROUBLE? Self-diagnostic function ExampleSupplies Types and sizes of copy paperSupplies Genuine supplies statementProper storage Store the supplies in a location that isSpecifications Specifications Optional Equipment Single Pass Feeder AR-SP2 SpecificationsPart Names Equipmentoptional Single Pass Feeder AR-SP2 Misfeed removalIndex Index Material Safety Data Sheet Ignition Temperature Special Fire Fighting ProcedureFlash Point Method Used Flammable LimitsIngredients CAS No Proportion Other LimitsRoutes of Entry Skin? Ingestion?None required under normal use Memo Memo Page Sharp Corporation

Related manuals

Manual 68 pages 6.94 Kb