Sharp M270, AR-M230 manual If a notice page is printed, When data loss error has occurred

Page 56

6

TROUBLESHOOTING

 

If a notice page is printed

(part 1)

If you find that a notice page has been printed at the end of a print job, the print data received from the computer has not been printed as specified. Fix the problem as explained below and then try printing again.

Notice Page regarding memory full on IMC board

****************************************************

Notice Page

****************************************************

The IMC memory full error had occurred, a normal output was not able to be executed.

Please refer to the operation manual for the solution method.

When the Staple function is not selected:

Disable the ROPM function by removing the checkmark from "ROPM" in the "Configuration" tab of the printer driver setup screen. (See "CONFIGURING THE PRINTER DRIVER" in the software setup guide for network printer.) If you need to use the ROPM function, lower the resolution setting in the printer driver or install more memory.

When the Staple function is selected:

Lower the resolution setting or increase the "MEMORY FOR PRINTER" setting in the key operator programs. If this does not resolve the problem, install more memory.

The IMC memory is used to store print data when the Note ROPM function is used. This memory is also used to

store original image data in the copy mode. The percentage of IMC memory allocated to the printer function can be adjusted using a key operator program. See "MEMORY FOR PRINTER" in the key operator's guide. The memory can be extended by adding commercially available memory modules. For details, contact your SHARP dealer.

When data loss error has occurred:

****************************************************

Notice Page

****************************************************

The data loss error had occurred, a normal output was not able to be executed.

Please refer to the operation manual for the solution method.

Set the page protection function or enable the ROPM function. To enable the ROPM function, select the "ROPM" checkbox in the "Configuration" tab of the printer driver setup screen. (See "CONFIGURING THE PRINTER DRIVER" in the software setup guide for network printer.)

PAGE PROTECTION

C O N T E N T S

I N D E X

56

 

 

 

Image 56
Contents AR-M230/M270 Series Online Manual for network printer Introduction Trademark AcknowledgmentsHow to use the online manual How to Control the Online ManualUsing Bookmarks How to Print Out This ManualContents Specifications Make sure that the on Line indicator on On Line indicator Data indicatorBasic printing Operation panel is litWindows 95/98/Me/NT When Forced Output of Print is disabledWhen Forced Output of Print is enabled Basic printing Auditing mode About the No Offset function settingWindows 2000/XP Printer driver settings Apply buttonTwo-sided printing Print data Printing result Sided Book Sided TabletPamphlet style Printing result Print data Right LeftPrinting multiple pages on one Fitting the printed image to the paper Rotating the print image 180 degrees Rotate 180 degreesHow to Print a Watermark Printing a watermarkWhen a finisher is installed Print data Printing resultWhen a saddle stitch finisher is installed Punch functionStaple Left Right StaplePrint hold function Hold After Print Hold Before PrintPrinting using the print hold function part How to print a print hold job Print and Save the Data key Points to note about the Print Hold functionPrinting begins Printing result when number of copies is Print data Collate Carbon copy printPrinting using carbon copy print Carbon Copy menuPrinting text and lines in black Printing text in blackPrinting lines in black Print data Printing result Text To BlackBefore using the Printer Status Monitor Printer utilitiesUsing the printer utilities Using the printer utilitiesPrinter Administration Utility Starting up the printer utilitiesChanging the Printer Status Monitor settings Right-click the Printer Status Monitor iconOn the task bar, and select Preferences from Pop-up menuChecking the printer status On the task bar, and select Sharp AR-XXXXStatus from the pop-up menu Click the Detail buttonStart the application and open the document Make sure that the correct printer is selectedConfigure print settings Click the Print buttonWhen Paper Feed is set to Auto Select When Paper Feed is set to paper tray or paper type Printing when auditing mode is enabled Using the print hold functionGiving priority to a print job Press the JOB Status keyTouch the Priority key Make sure that the Print JOB key isCanceling a print job You wish to cancelJob in progress and the jobs waiting to be Printed appear. Touch the key of the job thatHow to configure the settings Touch the Condition Settings keySetting screen Press the Print keyDesired item and touch the OK key More information on the condition setting screenTouch the desired setting on the setting screen Printer condition setting menu Condition Settings Default SettingsPrinter condition settings Default SettingsN T E N T S D E Sided PCL Settings PostScript Settings Printing the printer setting and font lists Press the Custom Settings keyTouch the list that you wish to print Touch the List Print keyTroubleshooting Printing does not take placePrinting does not take place Check the connectionsUSB or parallel connection in Windows Network connectionPoints to check on the Macintosh Check Your ComputerPoints to check in Windows Power switch on? Is the machine online? Check the machineHas the printer driver been installed properly? Checking the printer driverTwo-sided printing is not possible Improper printing operationPrinting is slow Improper printing operation Print quality is not satisfactory Check the paper being usedPart of the printed image is missing Printed image is coarsePrinted image is distorted When data loss error has occurred If a notice page is printedDisabling notice page printing Macintosh Mac OS 8.6 to Removing the softwareWindows Accessing the Web About the WebOpen the Web browser on your computer Address field of your Web browserSubmit Print Job setup Setting up the E-mail print function Configure the required e-mail settingsMail print function Link menu, click Direct PrintUsing the E-mail print function Function Command name Value Entry exampleDirectly printing a file in a computer Link menu, click Submit Print JobSelect the print format in Job Detail Click PrintInformation setup Smtp setupStatus message setup Link menu, click Status MessageDestination addresses and time schedule Click Submit to store the entered informationEnter the destination addresses Alerts message setupLink menu, click Alerts Message Enable Password Protection of this Web Site Link menu, click PasswordsClick Submit to store the entered passwords Printer specifications Index NumericsPrinter Utilities