TANDBERG ENTRYPOINT manual Configuring the IP Address via the Front Panel, Menu Hierarchy

Page 15

Configuring the IP Address via the Front Panel

TANDBERG ENTRYPOINT USER GUIDE

About Entrypoint Configuration

Configuring the IP Address via the Front Panel

The Entrypoint requires some basic configurations before it can be used. It is necessary to configure the IP-address and to create the dial-in and dial-out services to program the ISDN-PRI Line numbers.

Configuring via the Front Panel

The LCD panel makes it possible to configure and check the IP settings as well as to reboot the system. The front panel LCD menu items are as follows:

	Menu Hierarchy	IP Settings
		IP Address
	Main Menu	IP Netmask
		IP Default GW
	IP Settings

	IP Information	IP Information
	Commands
		IP Address

Switch on and press any key to produce the Main Menu. Use UP/DOWN to navigate to the IP Settings, if needed.

In addition to configure the IP address you must also configure the default-gateway, netmask and set IP assignment to static.

Use ENTER to enter Digit Altering Mode.

When finished editing use ESC to go to the Confirm change menu.

Presssubmenu.ENTER to access the IP Settings

Presscursor.ENTER again to produce the

Use UP/DOWN to alter the digit value.

Use the UP/DOWN key to select yes or no and ENTER to confirm.

Use the UP/DOWN keys to select IP Address.

Use up/down keys to navigate between the digits of the number.

Press ENTER as many times as needed to move to the next digit to be altered and alter this digit.

Use ESC key to navigate back to the main menu.

Commands

Reboot

DHCP assigned IP-addresses are supported by the TANDBERG Entrypoint (factory default).

Configuration via RS 232

UP key

ENTER key

As an alternative to the configuration via the LCD panel you may use RS 232 to configure and the system. This is treated on the previous page.

Switching On the Unit

Power switch

DOWN key

ESC key

Table of

Trademarks

&

Patents &

Safety/

To

Get You

Using the

Viewing the

Configuring

Maintenance

Services

Dial Plan

Contact

Contents

Copyright

Disclaimers

Environmental

Upup

and Going

Entrypoint

System Status

the

Entrypoint

&

Upgrade

Examples

Information

15

D 14050.04

10.2007

Image 15

Contents Guide Services Operator Safety / Environmental IssuesUsing the Entrypoint Maintenance and UpgradeCopyright 2007, Tandberg Trademarks and CopyrightDisclaimer, License Agreements, and Patent Information PatentsDisclaimers Disclaimer License Agreements Patent Information Safety Operator Safety / Environmental IssuesSafety Instructions Environmental Issues Tandberg Entrypoint To get You Up and Going Get YouGoing Connecting the Cables Unpacking and InstallationEntrypoint Features at a Glance About the Entrypoint Features HighlightsEntrypoint Capacity Typical Scenarios Entrypoint Start-up IndicatorDepending on the configuration ordered Front and Rear PanelsConfiguration via the Front Panel Configuring Your Entrypoint via the RS 232About Gateway Configuration Configuring via the RS 232Switching On the Unit Configuring the IP Address via the Front PanelConfiguring via the Front Panel Configuration via RS 232Using the Entrypoint Starting Up the Entrypoint Accessing the EntrypointForgot the Password? User name is adminManagement Menu An Overview of the Management Menu SystemOverview Window Remote Number. This is the inbound numberService Call Details About Service Call DetailsWhen View Details Has Been Selected Dial Extension IVR Example Call Setup via Default ServicesAbout Default Services Did Direct Inward DiallingDialling from Umts Using Phone Book Example of IVR Using the Phone BookAbout TMS Corporate Directory Viewing Viewing the System StatusAbout the Rear Panel LED Operation ISDN/PRI Status PRI Versions onlyISDN/BRI Status BRI Versions only Registration Status Rejected Gatekeeper StatusAbout H.323 Status Registration Status Registered Registration Status InactiveIVR ServicesSystem Information System Resources Configuring Configuring the EntrypointISDN/PRI Configuration ISDN/PRI Versions only Outgoing Bearer capabilityPrefix on National/International Numbers ISDN/BRI Configuration ISDN/BRI Versions only IP Configuration DNS InterfaceIP Address Assignment is Dhcp or Static Configuration Configuration paneAuthentication Mode is Off or Auto SIP settings SIP ConfigurationSave. Press Save to activate new settings Snmp ConfigurationSystem Maintenance and Upgrade MaintenanceUpgrade For dot-release upgrades a Release Key won’t be needed Maintenance GeneralUpgrading the System Maintenance Upgrading the SystemPress Add Option Maintenance Option Keys, Password and RestartOption Keys Password Restart Add Option key Key. ShowsServices Default Services About Default Services Service Configuration WindowConfiguration menu from the Service tab Example Dialplan ConfigurationAllow forwarding. After call Argument Details for the Default did ServiceDid Argument Details Under ArgumentsArgument Details for a Default IVR Service IVR Argument DetailsShow Dtmf Information Screen. This is a Menu Service Argument Details Argument Details for a Default Menu ServiceShow Dtmf Information Screen. Identical to TMS Corporate Directory Argument DetailsDial Plan Examples Dial PlanExamples Prefix See note below Some Dial Plan ExamplesAbout the Examples Example 1 Number-plan mappingDial Extension IVR Examples Dial Extension IVR Dial Plan ExamplesExample 6 3G to SIP IVR Forwarding and Use Remainder to On for a Secretary ServiceTMS Corporate Directory Contact Contact Information