TANDBERG ENTRYPOINT manual ISDN/PRI Status PRI Versions only, About the Rear Panel LED Operation

Page 23

ISDN/PRI Status (PRI Versions only)

TANDBERG ENTRYPOINT USER GUIDE

Select PRI Status to access the PRI Status pane.

The PRI status indication consist of 3 fields (see About the Rear Panel LED Operation below for PRI status):

Active – Indicates weather the PRI port is active or not.

Total number of channels – indicates the maximum available number of simultaneous ISDN slots (calls) per port; typically 30 for an E1 PRI and 8 for an E1 BRI.

Number of free channels – indicates the number of free B- channels on ISDN.

To view the ISDN PRI status, select the ISDN status item of the Status tab.

About the Rear Panel LED Operation

In addition to the web page indications, the ISDN interface also contains 4 LEDs, located at the the Entrypoint rear panel.

These LEDs indicate the following PRI status:

Green: Normal operation

Red Alarm or Loss of signal (LOS) indicates that there is no signal and thus no framing info received. A defect or unplugging the PRI cable will produce the same effect.

Yellow Alarm or Remote Alarm Indicator (RAI) means that the Entrypoint is receiving framing info, but in this framing info the other side tells the Entrypoint that it is not reading the Gateway’s transmitted framing info. Typically, this may be a broken connector in the transmit (TX) part of the PRI cable. This could also indicate weak or noisy signal in the transmit (TX) part of the PRI cable.

Blue Alarm indicates that the received frames are not synchronized properly.

No LED’s illuminate, indicates that layer one framing is working (right protocol like for example EURO ISDN selected), however there is a problem at layer 2 caused by for example a CRC4 configuration mismatch.

Table of

 

Trademarks

&

Patents &

 

Safety/

To

Get You

 

Using the

Viewing the

Configuring

 

Maintenance

 

Services

 

Dial Plan

 

Contact

Contents

 

Copyright

 

Disclaimers

 

Environmental

Up

and Going

 

Entrypoint

System Status

the Entrypoint

&

Upgrade

 

 

Examples

 

Information

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

23

 

 

 

 

 

 

 

 

 

 

D 14050.04

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10.2007

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Image 23
Contents Guide Services Operator Safety / Environmental IssuesUsing the Entrypoint Maintenance and UpgradeCopyright 2007, Tandberg Trademarks and CopyrightDisclaimers Disclaimer, License Agreements, and Patent InformationPatents Disclaimer License Agreements Patent Information Safety Operator Safety / Environmental IssuesSafety Instructions Environmental Issues Tandberg Entrypoint Going To get You Up and GoingGet You Connecting the Cables Unpacking and InstallationEntrypoint Capacity Typical Scenarios Entrypoint Features at a GlanceAbout the Entrypoint Features Highlights Entrypoint Start-up IndicatorDepending on the configuration ordered Front and Rear PanelsConfiguration via the Front Panel Configuring Your Entrypoint via the RS 232About Gateway Configuration Configuring via the RS 232Switching On the Unit Configuring the IP Address via the Front PanelConfiguring via the Front Panel Configuration via RS 232Using the Entrypoint Starting Up the Entrypoint Accessing the EntrypointForgot the Password? User name is adminManagement Menu An Overview of the Management Menu SystemOverview Window Remote Number. This is the inbound numberWhen View Details Has Been Selected Service Call DetailsAbout Service Call Details Dial Extension IVR Example Call Setup via Default ServicesAbout Default Services Did Direct Inward DiallingAbout TMS Corporate Directory Dialling from Umts Using Phone BookExample of IVR Using the Phone Book Viewing Viewing the System StatusAbout the Rear Panel LED Operation ISDN/PRI Status PRI Versions onlyISDN/BRI Status BRI Versions only Registration Status Rejected Gatekeeper StatusAbout H.323 Status Registration Status Registered Registration Status InactiveIVR ServicesSystem Information System Resources Configuring Configuring the EntrypointPrefix on National/International Numbers ISDN/PRI Configuration ISDN/PRI Versions onlyOutgoing Bearer capability ISDN/BRI Configuration ISDN/BRI Versions only IP Address Assignment is Dhcp or Static IP ConfigurationDNS Interface Authentication Mode is Off or Auto ConfigurationConfiguration pane SIP settings SIP ConfigurationSave. Press Save to activate new settings Snmp ConfigurationSystem Upgrade Maintenance and UpgradeMaintenance For dot-release upgrades a Release Key won’t be needed Maintenance GeneralUpgrading the System Maintenance Upgrading the SystemPress Add Option Maintenance Option Keys, Password and RestartOption Keys Password Restart Add Option key Key. ShowsServices Configuration menu from the Service tab Default ServicesAbout Default Services Service Configuration Window Example Dialplan ConfigurationAllow forwarding. After call Argument Details for the Default did ServiceDid Argument Details Under ArgumentsShow Dtmf Information Screen. This is a Argument Details for a Default IVR ServiceIVR Argument Details Menu Service Argument Details Argument Details for a Default Menu ServiceShow Dtmf Information Screen. Identical to TMS Corporate Directory Argument DetailsExamples Dial Plan ExamplesDial Plan Prefix See note below Some Dial Plan ExamplesAbout the Examples Example 1 Number-plan mappingExample 6 3G to SIP IVR Dial Extension IVR ExamplesDial Extension IVR Dial Plan Examples Forwarding and Use Remainder to On for a Secretary ServiceTMS Corporate Directory Contact Contact Information