TANDBERG ENTRYPOINT manual ISDN/BRI Configuration ISDN/BRI Versions only

Page 31

ISDN/BRI Configuration (ISDN/BRI Versions only)

TANDBERG ENTRYPOINT USER GUIDE

Select BRI to access the BRI Configuration pane.

Save. When all settings are entered, click on Save to make the new settings become effective.

You cannot configure ISDN BRI lines for special functions like

dial out only! The Gateway will automatically select a free BRI line for H.323 to 3G calls and possibly block a DiD or an IVR menu when the BRI lines have different numbers. Consequently, we strongly recommend that all ISDN BRI lines have the same number range!

Contact your ISDN or telecom supplier about numbering plans of ISDN lines.

BRI Protocol. Select between the following BRI protocols:

•ETSI (Euro ISDN)

•National ISDN

•AT&T Custom

•Japan/Taiwan ISDN

Outgoing Bearer capability. Within ISDN different bearer capabilities are used to signal the type of data (Voice, Data, H320, H.324M), which is used by telephony switches and other equipment to determine how to handle data or calls (compressing voice data neglect etc). The outgoing bearer capability sets the ISDN bearer capability for the outgoing telephone (voice only) and video telephone calls.

•H.324M: This ITU standardized capability is selected for outgoing calls by default.

•UDI: In some situations the switch does not accept calls which use the correct H.324M capability. This setting makes it possible to use the Entrypoint in these situations via selecting UDI.

All incoming calls are accepted independent of their bearer capabilities, therefore audio calls are accepted as well.

Table of

Trademarks

&

Patents &

Safety/

To

Get You

Using the

Viewing the

Configuring

Maintenance

Services

Dial Plan

Contact

Contents

Copyright

Disclaimers

Environmental

Up

and Going

Entrypoint

System Status

the

Entrypoint

& Upgrade

Examples

Information

31

D 14050.04

10.2007

Image 31

Contents Guide Services Operator Safety / Environmental IssuesUsing the Entrypoint Maintenance and UpgradeCopyright 2007, Tandberg Trademarks and CopyrightPatents Disclaimer, License Agreements, and Patent InformationDisclaimers Disclaimer License Agreements Patent Information Safety Operator Safety / Environmental IssuesSafety Instructions Environmental Issues Tandberg Entrypoint Get You To get You Up and GoingGoing Connecting the Cables Unpacking and InstallationAbout the Entrypoint Features Highlights Entrypoint Features at a GlanceEntrypoint Capacity Typical Scenarios Entrypoint Start-up IndicatorDepending on the configuration ordered Front and Rear PanelsConfiguration via the Front Panel Configuring Your Entrypoint via the RS 232About Gateway Configuration Configuring via the RS 232Switching On the Unit Configuring the IP Address via the Front PanelConfiguring via the Front Panel Configuration via RS 232Using the Entrypoint Starting Up the Entrypoint Accessing the EntrypointForgot the Password? User name is adminManagement Menu An Overview of the Management Menu SystemOverview Window Remote Number. This is the inbound numberAbout Service Call Details Service Call DetailsWhen View Details Has Been Selected Dial Extension IVR Example Call Setup via Default ServicesAbout Default Services Did Direct Inward DiallingExample of IVR Using the Phone Book Dialling from Umts Using Phone BookAbout TMS Corporate Directory Viewing Viewing the System StatusAbout the Rear Panel LED Operation ISDN/PRI Status PRI Versions onlyISDN/BRI Status BRI Versions only Registration Status Rejected Gatekeeper StatusAbout H.323 Status Registration Status Registered Registration Status InactiveIVR ServicesSystem Information System Resources Configuring Configuring the EntrypointOutgoing Bearer capability ISDN/PRI Configuration ISDN/PRI Versions onlyPrefix on National/International Numbers ISDN/BRI Configuration ISDN/BRI Versions only DNS Interface IP ConfigurationIP Address Assignment is Dhcp or Static Configuration pane ConfigurationAuthentication Mode is Off or Auto SIP settings SIP ConfigurationSave. Press Save to activate new settings Snmp ConfigurationSystem Maintenance Maintenance and UpgradeUpgrade For dot-release upgrades a Release Key won’t be needed Maintenance GeneralUpgrading the System Maintenance Upgrading the SystemPress Add Option Maintenance Option Keys, Password and RestartOption Keys Password Restart Add Option key Key. ShowsServices About Default Services Service Configuration Window Default ServicesConfiguration menu from the Service tab Example Dialplan ConfigurationAllow forwarding. After call Argument Details for the Default did ServiceDid Argument Details Under ArgumentsIVR Argument Details Argument Details for a Default IVR ServiceShow Dtmf Information Screen. This is a Menu Service Argument Details Argument Details for a Default Menu ServiceShow Dtmf Information Screen. Identical to TMS Corporate Directory Argument DetailsDial Plan Dial Plan ExamplesExamples Prefix See note below Some Dial Plan ExamplesAbout the Examples Example 1 Number-plan mappingDial Extension IVR Dial Plan Examples Dial Extension IVR ExamplesExample 6 3G to SIP IVR Forwarding and Use Remainder to On for a Secretary ServiceTMS Corporate Directory Contact Contact Information