Motorola P880 manual Speed Mode, Negotiation is enabled, this setting is, Ignored, Duplex Mode

Page 48

2

this value lower than 1024 (the output buffer’s capacity). Set this value lower if the port is experiencing overflow problems.

14.From the Pace Priority Mode pull-down menu, select Enable if you want this port to recognize and use 3Com’s PACE priority mechanism.

15.Click APPLY to save your changes, or CANCEL to restore previous settings.

Table10 describes the Fast Ethernet port parameters:

Table 10. Fast Ethernet (10/100) Port Parameters

Parameter

Definition

 

 

Name

A user-assigned name for this port (possibly a

 

drop name or the name of the station or other

 

device connected to the port).

 

 

Category

Allows you to select either User Port or Service

 

Port.

 

• The User Port is intended for use with

 

switch connections to end user nodes.

 

• The Service Port is intended for use with

 

switch connections to servers or other

 

switches. The Service Port allows the switch

 

to generate both log messages and alarm

 

messages (traps). The User Port only generates

 

log messages, preventing your network

 

management station from being

 

overwhelmed by port up/down messages

 

that result from users turning workstations

 

on and off.

 

 

Speed Mode

Allows you to select the speed of the port

 

manually (to either 10 or 100 Mb/s). If auto-

 

negotiation is enabled, this setting is

 

ignored.

 

 

Duplex Mode

Allows you set the port duplex mode (half- or

 

full-duplex).If auto-negotiation is enabled,

 

this setting is ignored.

 

 

2 - 14

Cajun P880 Routing Switch Installation Guide

Image 48
Contents Cajun P880 Switch Installation Guide Page Table of Contents Configuring the Cajun P880 Switch Appendix a Compliance and Specification Information Cajun P880 Switch Installation Guide Overview of The Contents Documentation FeedbackOnline Documentation ConventionsConvention Represents Examples Indicates a condition that may damage hardware orAudience Related DocumentsLucent Documents Reference DocumentsContacting Lucent Corporation Overview Verifying the System ComponentsThis unit has more than one power-supply cord. Disconnect All power cords Before servicing to avoid electric shockFrench GermanSelecting a Location Air Flow RequirementsInstalling the System Required Tools and HardwarePreventing Electrostatic Discharge Installing the Mounting Shelf Installing the Mounting ShelfInstalling the Chassis Rack Mounting the SystemSecuring the chassis to the Rack Attaching the Trim Pieces Finger PullsInstalling/Removing Power Supplies Installing the Power SupplyDevice Power Added/Used Installing/Removing Power Supplies Support the bottom of the power supply with your free handRemoving a Power Supply Removing a Power Supply Filler PanelConnecting the Power Supplies Removing Power Supply Filler PanelInstalling the Modules Installing ModulesInstalling the Cables Closing the Ejector TabsDistances 1000BASE-LX 1000BASE-SLXFiber Cable Description Maximum Cable Length Cable Description Maximum Cable LengthHalf-duplex connection 412 m Full-duplex connection Category 5 twisted pair cable 100 mInstalling the Cable Management Bracket Installing the Cable Management BracketInstalling/Removing Fan Assemblies Installing Chassis Fan Assemblies Replacing Fan AssembliesInstalling Rear Fan Assemblies Installing/Removing Switch Controllers/Elements Installing Redundant Controllers/ElementsInstalling Switch Elements/Switch Controllers Powering On the System Power-On SequenceModule Normal BehaviorPost Power-on Configuration Configuring the Cajun P880 Switch Series ModeSeries Mode Terminal Settings Configuring the Supervisor Module Using the CLIBaud Stop Bits Data Bits Flow Parity Rate Control 600 Xon/Xoff NoneCajun P880 Routing Switch Installation Guide Password Layer 2 Setup Command Display Configuring the Switch Using the Web Agent Cajun P880 SwitchSetting Up User Accounts Click Login. The Username/Password dialog box opensLogging Into the Web Agent Configuring Port Parameters Using the Web Agent Administrator ADUser Level Can Cannot UserConfiguring Physical Port Parameters on Gigabit Ports Parameter Definition Configuring Physical Port Parameters on Fast Ethernet Ports Fault DetectPort Pace PriorityCajun P880 Routing Switch Installation Guide Speed Mode Negotiation is enabled, this setting isDuplex Mode Full-duplex. If auto-negotiation is enabledFlow Control AutoNegotiation Speed/DuplexUsing the All Ports Configuration Dialog Box Burst SizeViewing Switch Port Parameters Configuring Switch Port Parameters Trunk Mode Parameter Definition Port VlanFrame Tags Known Mode Parameter Definition Vlan BindingAutomatic Vlan CreationConfiguring Port Vlan Parameters ClearIEEE-802.1Q Multi-layerOption Definition StaticBind to AllConfiguring VTP Snooping Configuring Non-VLAN Switch Port Parameters Parameter Recommended Setting Configuring Fast Start Mode Using the All Ports Configuration Dialog Box Setting Up Snmp Communities Community String field, enter a community nameAccess Level Manager Can Cannot Option Allows Access toChanging the Console Serial Port Settings Configuring Serial Console Port As a TTY ConsoleOption Default Available Settings Typical Connection Between the Switch and a Modem Disable DTR Configuring Dial-Up Networking Use flow control, click Software XON/XOFF Cajun P880 Routing Switch Installation Guide Configuring a Static Route for the PPP Console Hardware Requirements for RoutingMask field, enter the network mask IP address Configuring IP Routing on the Switch Configuring System Information Entering General System InformationSetting Summer Time Hours Enabling SntpSummer Time Hours Click RecurringRecurring StartEnd WeekSelect Recurring DayMonth HourClick One-Time One-timeSelect the week of the month during which you Setting the System Clock Setting the Temperature System Displaying the Power System StatisticsConfiguring Redundant Hardware Displaying Cooling System StatisticsChecking for Proper Installation Properly-Installed Redundant Hardware Settings Replacing the Primary ControllerReplacing an Element Managing Configuration Files Performing a System ResetViewing Your Running Configuration Viewing Your Startup ConfigurationViewing Your Script Execution Log File Copying Configuration Files Copying Running Configuration to Startup ConfigurationCopying Files Parameter Description Options Copy Destination DestinationFilename Tftp Server IPCajun P880 Routing Switch Installation Guide Viewing the Status of a Tftp Transfer Get Status of Most Recent Tftp Copy field, click StatusCajun P880 Routing Switch Installation Guide Safety PowerOperating/Physical Index NumericsCLI Cajun P880 Switch Installation Guide Cajun P880 Switch Installation Guide Cajun P880 Switch Installation Guide Cajun P880 Switch Installation Guide Cajun P880 Switch Installation Guide Cajun P880 Switch Installation Guide Cajun P880 Switch Installation Guide Cajun P880 Switch Installation Guide