Motorola P880 manual Parameter Definition, Disable DTR

Page 66

2

To configure the console serial port as a PPP console:

1.In the System Configuration section of the Web Agent window, select Console Configuration. The Console Configuration dialog box opens.

2.Click PPP for your console type and click Select. The Console Port Configuration dialog box opens.

3.Use Table22 to change your console port settings.

*Note: The only parameters you can change as a PPP console is baud rate and flow control. The flow control settings are limited to None or Xon/Xoff.

4.In the Modem Init Cmd field, enter your modem initialization command. The default modem configuration string is AT&D0S0=1.

Table 23. Modem Configuration String Parameters

Parameter

Definition

 

 

&D0

Disable DTR

 

 

S0=1

Auto-answer mode (one ring)

 

 

CD follows carrier

Depends on modem

 

 

E0

Disable local echo

 

 

Software Flow Control

Depends on modem

(Receive and Transmit)

 

 

 

5.Click APPLY to save your changes, or CANCEL to restore previous settings.

*Note: If you misconfigure your PPP serial console port, you can regain CLI access to correct the configuration parameters. For more information, refer to “Regaining Configuration Access to the PPP Serial Port Console”.

Safety Tip: To successfully dial-in with PPP to the switch, you must also configure an IP address and interface for the PPP Serial Interface (Serial-Console).

2 - 32

Cajun P880 Routing Switch Installation Guide

Image 66
Contents Cajun P880 Switch Installation Guide Page Table of Contents Configuring the Cajun P880 Switch Appendix a Compliance and Specification Information Cajun P880 Switch Installation Guide Overview of The Contents Documentation FeedbackConvention Represents Examples Online DocumentationConventions Indicates a condition that may damage hardware orLucent Documents AudienceRelated Documents Reference DocumentsContacting Lucent Corporation Overview Verifying the System ComponentsFrench This unit has more than one power-supply cord. DisconnectAll power cords Before servicing to avoid electric shock GermanSelecting a Location Air Flow RequirementsInstalling the System Required Tools and HardwarePreventing Electrostatic Discharge Installing the Mounting Shelf Installing the Mounting ShelfInstalling the Chassis Rack Mounting the SystemSecuring the chassis to the Rack Attaching the Trim Pieces Finger PullsInstalling/Removing Power Supplies Installing the Power SupplyDevice Power Added/Used Installing/Removing Power Supplies Support the bottom of the power supply with your free handRemoving a Power Supply Removing a Power Supply Filler PanelConnecting the Power Supplies Removing Power Supply Filler PanelInstalling the Modules Installing ModulesInstalling the Cables Closing the Ejector TabsDistances 1000BASE-LX 1000BASE-SLXHalf-duplex connection 412 m Full-duplex connection Fiber Cable Description Maximum Cable LengthCable Description Maximum Cable Length Category 5 twisted pair cable 100 mInstalling the Cable Management Bracket Installing the Cable Management BracketInstalling/Removing Fan Assemblies Installing Chassis Fan Assemblies Replacing Fan AssembliesInstalling Rear Fan Assemblies Installing/Removing Switch Controllers/Elements Installing Redundant Controllers/ElementsInstalling Switch Elements/Switch Controllers Module Powering On the SystemPower-On Sequence Normal BehaviorPost Power-on Configuration Configuring the Cajun P880 Switch Series ModeSeries Mode Baud Stop Bits Data Bits Flow Parity Rate Control Terminal SettingsConfiguring the Supervisor Module Using the CLI 600 Xon/Xoff NoneCajun P880 Routing Switch Installation Guide Password Layer 2 Setup Command Display Configuring the Switch Using the Web Agent Cajun P880 SwitchSetting Up User Accounts Click Login. The Username/Password dialog box opensLogging Into the Web Agent User Level Can Cannot Configuring Port Parameters Using the Web AgentAdministrator AD UserConfiguring Physical Port Parameters on Gigabit Ports Parameter Definition Port Pace Configuring Physical Port Parameters on Fast Ethernet PortsFault Detect PriorityCajun P880 Routing Switch Installation Guide Duplex Mode Speed ModeNegotiation is enabled, this setting is Full-duplex. If auto-negotiation is enabledNegotiation Flow ControlAuto Speed/DuplexUsing the All Ports Configuration Dialog Box Burst SizeViewing Switch Port Parameters Configuring Switch Port Parameters Trunk Mode Parameter Definition Port VlanFrame Tags Automatic Vlan Known ModeParameter Definition Vlan Binding CreationIEEE-802.1Q Configuring Port Vlan ParametersClear Multi-layerBind to Option DefinitionStatic AllConfiguring VTP Snooping Configuring Non-VLAN Switch Port Parameters Parameter Recommended Setting Configuring Fast Start Mode Using the All Ports Configuration Dialog Box Setting Up Snmp Communities Community String field, enter a community nameAccess Level Manager Can Cannot Option Allows Access toChanging the Console Serial Port Settings Configuring Serial Console Port As a TTY ConsoleOption Default Available Settings Typical Connection Between the Switch and a Modem Disable DTR Configuring Dial-Up Networking Use flow control, click Software XON/XOFF Cajun P880 Routing Switch Installation Guide Configuring a Static Route for the PPP Console Hardware Requirements for RoutingMask field, enter the network mask IP address Configuring IP Routing on the Switch Configuring System Information Entering General System InformationSetting Summer Time Hours Enabling SntpSummer Time Hours Click RecurringEnd RecurringStart WeekMonth Select RecurringDay HourClick One-Time One-timeSelect the week of the month during which you Setting the System Clock Setting the Temperature System Displaying the Power System StatisticsConfiguring Redundant Hardware Displaying Cooling System StatisticsChecking for Proper Installation Properly-Installed Redundant Hardware Settings Replacing the Primary ControllerReplacing an Element Managing Configuration Files Performing a System ResetViewing Your Running Configuration Viewing Your Startup ConfigurationViewing Your Script Execution Log File Copying Configuration Files Copying Running Configuration to Startup ConfigurationCopying Files Parameter Description Options Filename Copy DestinationDestination Tftp Server IPCajun P880 Routing Switch Installation Guide Viewing the Status of a Tftp Transfer Get Status of Most Recent Tftp Copy field, click StatusCajun P880 Routing Switch Installation Guide Safety PowerOperating/Physical Index NumericsCLI Cajun P880 Switch Installation Guide Cajun P880 Switch Installation Guide Cajun P880 Switch Installation Guide Cajun P880 Switch Installation Guide Cajun P880 Switch Installation Guide Cajun P880 Switch Installation Guide Cajun P880 Switch Installation Guide Cajun P880 Switch Installation Guide