Motorola P880 manual Parameter Recommended Setting

Page 59

Examples of Switch Ports Settings for Various VLAN Connection Types

3.From the Spanning Tree pull-down menu, select to Enable or Disable spanning tree protocol on this port.

4.From the Fast Start pull-down menu, select to Enable or Disable. When enabled, Fast Start mode ports begin forwarding traffic without waiting for the spanning tree negotiation to complete. Fast start eliminates the waiting time of listen and learn states. Ports immediately enter the forward state.

5.From the Known Mode pull-down menu, select to Enable or Disable. Selecting Enable limits the packets with unknown unicast destination addresses flooded to this port. For example, if a known end-station or file server is connected to the port, there’s no need to flood unknown unicasts to that port. You must manually enter a static MAC address for the station actually attached to the port.

6.From the 3Com Mapping Table pull-down menu, select an assignment to specify how incoming tagged frames from 3Com equipment are mapped to Lucent VLANs. Refer to “Creating 3Com Mapping Tables”, in the Cajun P550/P220 Switch Operation Guide, for more information on 3Com Mapping Tables.

7.Click APPLY to save your changes, or CANCEL to restore previous settings.

Use Table 16 through Table18 for recommended switch port settings for each connection type.

Table 16. Example 1. Trunk to Cisco Catalyst 5000 TM

Parameter

Recommended Setting

 

 

Port VLAN

Default - causes untagged packets to be

 

assigned to the default VLAN.

 

 

Trunk Mode

Multi-level- causes the port to send frames

 

using the multilevel format.

 

 

VLAN Binding

Bind to All - binds the port to all VLANs

 

known to the switch.

 

 

Automatic

Enable - causes the switch to learn new VLAN

VLAN Creation

IDs that arrive at the port, and then bind the

 

port to these VLANs.

 

 

VTP Snooping

Enable - cause the switch to update its VLANs

 

as they are created, deleted, or changed on the

 

Catalyst.

 

 

Cajun P880 Routing Switch Installation Guide

2 - 25

Image 59
Contents Cajun P880 Switch Installation Guide Page Table of Contents Configuring the Cajun P880 Switch Appendix a Compliance and Specification Information Cajun P880 Switch Installation Guide Documentation Feedback Overview of The ContentsIndicates a condition that may damage hardware or Online DocumentationConventions Convention Represents ExamplesReference Documents AudienceRelated Documents Lucent DocumentsContacting Lucent Corporation Verifying the System Components OverviewGerman This unit has more than one power-supply cord. DisconnectAll power cords Before servicing to avoid electric shock FrenchAir Flow Requirements Selecting a LocationPreventing Electrostatic Discharge Installing the SystemRequired Tools and Hardware Installing the Mounting Shelf Installing the Mounting ShelfRack Mounting the System Installing the ChassisSecuring the chassis to the Rack Finger Pulls Attaching the Trim PiecesDevice Power Added/Used Installing/Removing Power SuppliesInstalling the Power Supply Support the bottom of the power supply with your free hand Installing/Removing Power SuppliesRemoving a Power Supply Filler Panel Removing a Power SupplyRemoving Power Supply Filler Panel Connecting the Power SuppliesInstalling Modules Installing the ModulesClosing the Ejector Tabs Installing the Cables1000BASE-LX 1000BASE-SLX DistancesCategory 5 twisted pair cable 100 m Fiber Cable Description Maximum Cable LengthCable Description Maximum Cable Length Half-duplex connection 412 m Full-duplex connectionInstalling the Cable Management Bracket Installing the Cable Management BracketInstalling/Removing Fan Assemblies Replacing Fan Assemblies Installing Chassis Fan AssembliesInstalling Rear Fan Assemblies Installing Redundant Controllers/Elements Installing/Removing Switch Controllers/ElementsInstalling Switch Elements/Switch Controllers Normal Behavior Powering On the SystemPower-On Sequence ModulePost Power-on Configuration Series Mode Configuring the Cajun P880 SwitchSeries Mode 600 Xon/Xoff None Terminal SettingsConfiguring the Supervisor Module Using the CLI Baud Stop Bits Data Bits Flow Parity Rate ControlCajun P880 Routing Switch Installation Guide Password Layer 2 Setup Command Display Cajun P880 Switch Configuring the Switch Using the Web AgentLogging Into the Web Agent Setting Up User AccountsClick Login. The Username/Password dialog box opens User Configuring Port Parameters Using the Web AgentAdministrator AD User Level Can CannotConfiguring Physical Port Parameters on Gigabit Ports Parameter Definition Priority Configuring Physical Port Parameters on Fast Ethernet PortsFault Detect Port PaceCajun P880 Routing Switch Installation Guide Full-duplex. If auto-negotiation is enabled Speed ModeNegotiation is enabled, this setting is Duplex ModeSpeed/Duplex Flow ControlAuto NegotiationBurst Size Using the All Ports Configuration Dialog BoxViewing Switch Port Parameters Configuring Switch Port Parameters Frame Tags Trunk ModeParameter Definition Port Vlan Creation Known ModeParameter Definition Vlan Binding Automatic VlanMulti-layer Configuring Port Vlan ParametersClear IEEE-802.1QAll Option DefinitionStatic Bind toConfiguring VTP Snooping Configuring Non-VLAN Switch Port Parameters Parameter Recommended Setting Configuring Fast Start Mode Using the All Ports Configuration Dialog Box Community String field, enter a community name Setting Up Snmp CommunitiesOption Allows Access to Access Level Manager Can CannotOption Default Available Settings Changing the Console Serial Port SettingsConfiguring Serial Console Port As a TTY Console Typical Connection Between the Switch and a Modem Disable DTR Configuring Dial-Up Networking Use flow control, click Software XON/XOFF Cajun P880 Routing Switch Installation Guide Mask field, enter the network mask IP address Configuring a Static Route for the PPP ConsoleHardware Requirements for Routing Configuring IP Routing on the Switch Entering General System Information Configuring System InformationEnabling Sntp Setting Summer Time HoursClick Recurring Summer Time HoursWeek RecurringStart EndHour Select RecurringDay MonthOne-time Click One-TimeSelect the week of the month during which you Setting the System Clock Displaying the Power System Statistics Setting the Temperature SystemDisplaying Cooling System Statistics Configuring Redundant HardwareChecking for Proper Installation Replacing the Primary Controller Properly-Installed Redundant Hardware SettingsReplacing an Element Performing a System Reset Managing Configuration FilesViewing Your Script Execution Log File Viewing Your Running ConfigurationViewing Your Startup Configuration Copying Files Copying Configuration FilesCopying Running Configuration to Startup Configuration Parameter Description Options Tftp Server IP Copy DestinationDestination FilenameCajun P880 Routing Switch Installation Guide Get Status of Most Recent Tftp Copy field, click Status Viewing the Status of a Tftp TransferCajun P880 Routing Switch Installation Guide Power SafetyOperating/Physical Numerics IndexCLI Cajun P880 Switch Installation Guide Cajun P880 Switch Installation Guide Cajun P880 Switch Installation Guide Cajun P880 Switch Installation Guide Cajun P880 Switch Installation Guide Cajun P880 Switch Installation Guide Cajun P880 Switch Installation Guide Cajun P880 Switch Installation Guide