Accton Technology CheetahSwitch Workgroup, 4508 manual Configuring Igmp

Page 36

CheetahSwitch Workgroup-4508

Configuring IGMP

This protocol allows a host to inform its local switch/router that it wants to receive transmissions addressed to a specific multicast group. You can use the IGMP Configuration screen to configure multicast filtering shown below:

	CheetahSwitch Workgroup - 4508
	IGMP Configuration
IGMP Status		: ENABLED
Act as IGMP Querier		: DISABLED
IGMP Query Count		: 5
IGMP Report Delay (Minutes)		: 5
<APPLY>	<OK>	<CANCEL>
Use <TAB> or arrow keys to move, <Space> to scroll options.

Parameter	Description
IGMP Status	If enabled, the switch will monitor network traffic to determine which
	hosts want to receive multicast traffic.
Act as IGMP Querier	If enabled, the switch can serve as the “querier,” which is responsible
	for asking hosts is they want to receive multicast traffic. (Not
	implemented in the current firmware release.)
IGMP Query Count	The maximum number of queries issued for which there has been no
	response before the switch takes action to solicit reports.
IGMP Report Delay	The time (in minutes) between receiving an IGMP Report for an IP
	multicast address on a port before the switch sends an IGMP Query
	out that port and removes the entry from its list.

Note: The default values are indicated in the sample screen.

2-24

Image 36

Contents CheetahSwitch Workgroup-4508 Management Guide CheetaSwitch Workgroup-4508 International Headquarters USA Headquarters RMAPage Contents Using the Web Agent Appendix a Troubleshooting Advanced TopicsAppendix B Pin Assignments IiiPage Managing the Switch Configuration OptionsMaking Connections for System Configuration CheetahSwitch Workgroup-4508Onsite Connection Modem ConnectionManagement Guide Telnet Connection In-Band Network ConnectionCheetahSwitch Workgroup-4508 Using the System Configuration Program Main Menu Parameter DescriptionManagement Guide Parameter DescriptionSystem Information Menu Displaying System InformationManagement Setup Menu Management Guide Displaying Version InformationChanging the Network Configuration IP Configuration Access Host Configuration IP Connectivity Test PingHttp Configuration CheetahSwitch Workgroup-4508 Configuring the Serial Port Parameter Default DescriptionManagement Guide Assigning Snmp Parameters Configuring Community Names Configuring IP Trap ManagersConsole Login Configuration CheetahSwitch Workgroup-4508 Downloading System Software Using Tftp Protocol to Download Over the NetworkConfiguring the Switch CheetahSwitch Workgroup-4508 Configuring Port Parameters EnabledManagement Guide Viewing the Current Port Configuration Using the Spanning Tree AlgorithmConfiguring Bridge STA Priority 32,768Configuring STA for Ports DisabledDisplaying the Current Bridge STA Displaying the Current STA for Ports Information. Port address table is cleared, and the port Management Guide Using a Mirror Port for Analysis Igmp Multicast FilteringConfiguring Igmp Management Guide Broadcast Storm Control Refer to Network Monitor Menu / Static Unicast Address Table Management Guide Configuring Traffic Classes Port Priority Configuration802.1p Port Traffic Class Information Management Guide Configuring Virtual LANs 802.1Q Vlan Base InformationMAX Vlan ID 802.1Q Vlan Current Table Information VID802.1Q Vlan Static Table Configuration 802.1Q Vlan Port Configuration PvidMonitoring the Switch Menu DescriptionCheetahSwitch Workgroup-4508 Displaying Port Statistics Displaying Rmon Statistics Formed Using the Address Table MACVlan ID assigned to this multicast group Multicast IP Management Guide Configuring Static Unicast Addresses ParameterVID MAC Resetting the System Logging Off the SystemPost Using the Web Agent Navigating the Web Browser InterfaceCheetahSwitch Workgroup-4508 Home Console Configuration Panel DisplaySnmp STAVlan System Information Switch Information Main BoardNetwork Configuration IP ConfigurationSnmp Configuration CheetahSwitch Workgroup-4508 Access HostSnmp Administration Enable Management Guide Snmp Community Trap ManagersSecurity Configuration Firmware Upgrade OptionsChange Password Web Upload ManagementTftp Download Management Address Table Configuration Spanning Tree Information Spanning TreePorts Management Guide Spanning Tree Configuration Switch Parameter Default DescriptionWhen the Switch Becomes Root Parameter Default Description STA Port Configuration Path Cost 100/19/4Configuring Bridge MIB Extensions Bridge CapabilityBridge Settings Port Priority ConfigurationPriority Port Traffic Class Information Configuring VLANs Vlan Basic InformationManagement Guide Vlan Current Table Vlan IDCheetahSwitch Workgroup-4508 Vlan Static List Vlan Static TableVlan Static Membership by Port CheetahSwitch Workgroup-4508 Vlan Port Configuration Configuring Igmp Igmp Multicast FilteringPort Menus Port InformationPort Configuration Port Mirroring Configuration Port StatisticsEtherlike Statistics Sum of alignment errors and code errors frames received with CheetahSwitch Workgroup-4508 Rmon Statistics Undersize FramesFCS or alignment error Broadcast Storm Control Advanced Topics Spanning Tree AlgorithmVirtual LANs Assigning Ports to VLANsManagement Guide Vlan Classification Port OverlappingForwarding Tagged/Untagged Frames Class-of-Service CoS Support Igmp Snooping and IP Multicast FilteringSnmp Management Software Remote MonitoringCheetahSwitch Workgroup-4508 Console Connection In-Band ConnectionUpgrading Firmware via the Serial Port Loader Connection from Switch’s Serial Port to PC’s 9-Pin COM Port DB9 Serial Port Pin DescriptionDB9 Port Pin Assignments Connection from Switchs Serial Port to PCs 25-Pin DTE Port Switchs 9-Pin Ccitt Signal Modems Serial Port Pin COM PortSwitchs 9-Pin Serial Null Modem PortES4508 E022000-R01