Paxar 9844, 9854 manual General safety notes, Service

Page 4

05/08 Rev. ABOPERATOR’S HANDBOOKSafety

General safety notes

 

CAUTION! - The printer operates safely when you observe all necessary

 

information.

 

Proper operation of the product requires the user to read and follow these

 

operating instructions. The warranty does not cover service required as a

 

result of operator error and/or failure to read and follow the documentation.

 

 

 

 

 

WARNING! - Any changes or modifications not expressly approved by us

 

could void the user's authority to operate the equipment.

 

Only operate the printer using the system voltage indicated on the

 

nameplate!

 

Only connect the printer to a grounded power outlet.

 

Only use the printer within specified environmental conditions!

 

Only operate the printer when the cover is closed!

 

Only trained and authorized personnel should operate the printer!

 

During operation, the printhead can become hot! Be careful when touching

 

the printhead!

 

Do not make any modifications to the printer!

 

Do not spill any liquids into the printer!

 

Repairs to the device must be performed by authorized specialists!

 

Before cleaning the printer, turn off the printer and disconnect the power

 

supply!

 

Only use original accessories!

 

Connect the printer only to other devices that fulfil SELV (safety extra-low

 

voltage) circuit requirements to EN 60950!

 

Keep long hair, loose jewelry, long sleeves, etc. away from the printer

 

during operation.

 

Wear sufficient personal protection gear.

 

The printer can only be disconnected completely by removing the power

 

supply cable. For this reason:

 

Make sure that the printer’s power supply socket is readily accessible!

 

In case of emergency, turn off the printer and disconnect the power supply

 

cable!

 

 

 

Keep these operating instructions in a safe place and make sure they are

 

read.

 

The printer must be operated, adjusted and serviced by instructed and

 

authorized personnel.

 

Carefully follow all procedures listed in this manual.

Service

Special servicing, error searching and error correction are to be performed by

 

authorized personnel.

Image 4
Contents Operators Handbook Copyright Safety Information General safety notes ServiceEquipment safety Disposal Procedures Battery Disposal InformationFCC Regulations Class B Canadian D.O.C. WarningTable of Contents Getting Started Unpacking the printer Installing the PrinterCarrying the Printer Printer Contents Removing the Transportation LockTerms to Know About the Printer Exterior view of the printerPeel and Liner TakeupDispenser Mode with Dispensing Edge Sensor About the 9854 Dispenser Peel and Internal Liner TakeupStart/stop signal input Serial Interface Identifying Printer ConnectionsSafety Information Using the Control Panel Display Online Mode Offline ModeOperating Modes Mode StandaloneOnly Using the Printer Connecting the PrinterSetting the Interface Using the 9854 Printer with Internal Liner TakeupDisable EnableUsing the 9854 Printer with Dispenser Parameter Possible SettingsConfiguring Offline OperationPosition Label lengthOnline Operation Print InfoCreating a Print job Sending a Print JobWindows Printer DriverUsing Compact Flash Cards Compact FlashCard Inserting a CF cardSetting the Realtime Clock 9854 only Outputting the realtime clock value using Easy PlugSetup Loading Diagrams Material and ribbon path in printerPrinter with Internal Liner Takeup Reel Rewinder Printer with Dispenser Peel Material and ribbon path through printer with dispenser peelAbout Material Selecting Ribbon/MaterialAbout Ribbons Loading Material Ÿ ž Loading Fan-fold Material Loading the 9854 with Internal Liner Takeup Reel Dispensing Peel 9854 only Loading a Ribbon Replacing a used ribbonQuick ribbon exchange Material Stock End Material/Ribbon EndRibbon End Setting Printhead Support Adjusting wheel for the printhead supportSetting the Material Parameters ParameterOPERATOR’S Handbook Care & Maintenance Care & Maintenance SafetyTroubleshooting Calling Technical Support Frequency of CareCleaning with the cleaning pen order part number Cleaning the PrintheadCleaning with isopropyl alcohol Replacing the Printhead Connecting the printheadRemoving the printhead Cleaning the Print Roller ™ šCleaning the Punch Die Cut Sensor Specifications Specifications PrintersSupplies Material Ribbon FoilSpecifications Page Toll Free