Wayne-Dalton WDSF-10, WDUSB-10R manual Common Operations

Page 11

Drawing Floor Plan

You may optionally draw a basic floor plan or room layout in the software for organizing your Z-Wave®modules.

1.To draw a room, click the DRAW ROOMS button in the Design pane. This will enable DRAW ROOMS

	mode. To exit this mode, click the	Click on DRAW ROOMS to enter
	DRAW ROOMS button again.	Click on DRAW ROOMS to enter
	DRAW ROOMS button again.	or leave drawing mode.
	Once in this mode, you may draw	or leave drawing mode.
	Once in this mode, you may draw
	one or more rooms.

To draw a room:

•Move your mouse pointer to the location in the open center area of the software interface where you would like to draw your room. This will be one corner of the room.

•Press the left button on your

mouse and then move your mouse diagonally to where the opposite corner of the room should be.

•To complete the room, release

	the left mouse button.	Example of Floor Layout.
	• When prompted, type a name	Example of Floor Layout.
	• When prompted, type a name
	for the room.

To draw a non-rectangular room:

•Draw the largest rectangular section of the room per the above instructions.

•To draw an additional segment of the room, press the left mouse button inside the room and then move your mouse diagonally to an empty area outside of the room.

•To complete the extension to the room, release the left mouse button.

•To erase unwanted sections

of the room, use the ERASE mode (See next section).

Continued next page...

Common Operations

11

Image 11

Contents Home Control Basics Package Contents USB Z-Wave Adapter USB Stand Software on CDTable of Contents Copy See Replicate BasicsBasics Number below corresponds to the bubble number above Basics 143Screen Layout Information Install USB Adapter and USB stand into computer USB port Installation/SetupUse Change Location link to set your physical location NextPress ADD Device to add a Z-Wavemodule Adding Modules to the NetworkHide Pane Button or Design tab to reveal the icon Operation Common Operations Erase Drawing Floor PlanButton in the Design pane. This AgainPress Remove Device to remove a Z-Wavemodule Right-click and select Remove Broken Device Remove/Replace Broken ModulesTo remove the module from Locking/Unlocking ThinkEssentials Use the following procedure to lock/unlock ThinkEssentialsLocked mode the software OperationsScenes/Zones To include modules into this scene Remove Zone option respectively Modifying Scenes/ZonesSelect Scene/Zone and Action desired SchedulesActivated  Items LinkModify the desired fields per Instructions in the section PagesJoining ThinkEssentials to Existing Networks Network OperationsInitiate Primary Controller to Send Replication ExamplePrimary Controller Press ADD Device to add a secondary controller Adding a Controller To the networkSecondary Controller Device removed successfully message window Updating Secondary Controllers Polling Advanced OperationsOptimize/Repair Network Confirmation of successful transfer Transfer Primary Role From ThinkessentialsInitiate Transfer in ThinkEssentials Example Portable ControllerCONTROLLER, or Controller Shift On Settings tab, select Switch to or JoinController Shift command Transfer Primary Role To ThinkessentialsConfiguration Backup Network SettingsWayne-Dalton USB Z-Wave Restore commandClick the Backup or Restore Network Settings link Backup fileBefore you begin, you must Exit Located. Note The default parent directory isCommand line window Section on the Settings tabModify the Target , then click on APPLY, then OK Adding Command Line Option to ThinkEssentials ShortcutStart ThinkEssentials using the ThinkEssentials icon ThinkEssentials /multi Command Line Option Multiple Z-WaveUSB AdaptersInitiate command line function Type in the /multi command line optionInitiate command line function Press F5 to refresh and poll the network ShortcutsExiting/Closing Again On the Settings tab, click on the Reset link Factory ResetResetting Thinkessentials To reset the USB Z-Wave AdapterTroubleshooting Some modules do not support It is enabled on the desired days of weekIf the modules’s icon is covered by a red Then select the module againController to my network. Now, neither Set up your network againCheck to make sure that there is power Switched onUS and Foreign Patents pending Compliance