Wayne-Dalton WDSF-10, WDUSB-10R manual Compliance, US and Foreign Patents pending

Page 42

Compliance

US and Foreign Patents pending

 

ThinkEssentials® is a registered trademark of Controlthink LC

All Rights Reserved.

Portions of this manual Copyright © 2005-2007 Controlthink LC.

Z-Wave® is a registered trademark of Zen-Sys Corporation

 

Windows XP and Vista are registered trademarks of Microsoft Corporation

FCC and IC Statement

FCC Regulatory Information: NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

a)reorient or relocate the receiving antenna,

b)increase the separation between the equipment and receiver,

c)connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

IC Regulatory Information: This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device.

Cet appareillage numérique de la classe B répond a toutes les exigences de l’interférence canadienne causant des règlements d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée.

WARNING: Changes or modifications to this receiver not expressly approved by Wayne-Dalton Corp. could void the user’s authority to operate this equipment.

© Copyright 2007 Wayne-Dalton Corp. Part No. 0002420 Rev. ANew 11/26/07

For Assistance, you may reach us online at www.wayne-dalton.com/access

42

Page 41 Page 42
Image 42
Page 41 Page 42
Contents Package Contents USB Z-Wave Adapter USB Stand Software on CD Home Control BasicsTable of Contents Basics Copy See ReplicateBasics Basics 143 Screen Layout InformationNumber below corresponds to the bubble number above Installation/Setup Install USB Adapter and USB stand into computer USB portNext Use Change Location link to set your physical locationAdding Modules to the Network Press ADD Device to add a Z-WavemoduleHide Pane Button or Design tab to reveal the icon Operation Common Operations Again Drawing Floor PlanButton in the Design pane. This ErasePress Remove Device to remove a Z-Wavemodule Remove/Replace Broken Modules To remove the module fromRight-click and select Remove Broken Device Operations Use the following procedure to lock/unlock ThinkEssentialsLocked mode the software Locking/Unlocking ThinkEssentialsScenes/Zones To include modules into this scene Modifying Scenes/Zones Remove Zone option respectivelySchedules Select Scene/Zone and Action desired  ActivatedPages LinkModify the desired fields per Instructions in the section ItemsNetwork Operations Joining ThinkEssentials to Existing NetworksExample Primary ControllerInitiate Primary Controller to Send Replication Adding a Controller To the network Secondary ControllerPress ADD Device to add a secondary controller Device removed successfully message window Updating Secondary Controllers Advanced Operations Optimize/Repair NetworkPolling Example Portable Controller Transfer Primary Role From ThinkessentialsInitiate Transfer in ThinkEssentials Confirmation of successful transferTransfer Primary Role To Thinkessentials On Settings tab, select Switch to or JoinController Shift command CONTROLLER, or Controller ShiftBackup Network Settings ConfigurationBackup file Restore commandClick the Backup or Restore Network Settings link Wayne-Dalton USB Z-WaveSection on the Settings tab Located. Note The default parent directory isCommand line window Before you begin, you must ExitAdding Command Line Option to ThinkEssentials Shortcut Start ThinkEssentials using the ThinkEssentials iconModify the Target , then click on APPLY, then OK Type in the /multi command line option Command Line Option Multiple Z-WaveUSB AdaptersInitiate command line function ThinkEssentials /multiInitiate command line function Shortcuts Press F5 to refresh and poll the networkExiting/Closing To reset the USB Z-Wave Adapter Factory ResetResetting Thinkessentials Again On the Settings tab, click on the Reset linkTroubleshooting Then select the module again It is enabled on the desired days of weekIf the modules’s icon is covered by a red Some modules do not supportSwitched on Set up your network againCheck to make sure that there is power Controller to my network. Now, neitherCompliance US and Foreign Patents pending
Top Page Image Contents