Wayne-Dalton WDUSB-10 manual Adding Modules to the Network, Press ADD Device to add a Z-Wavemodule

Page 8

Adding Modules to the Network

1.From the Design tab, press the ADD DEVICE button. A message window will ask you to press the button on the device to add.

2.Press-and-release the PROGRAM button on the Z-Wave®module. If successful, a message window will appear stating that the device has been successfully added. Repeat this procedure if a message window states that the module failed to be included.

NOTE: For your security, the USB Z-Wave®Adapter must be within 3 feet of the Z-Wave®module to be added. If this is not possible, please set up your network with a portable remote controller and then copy this information to the USB adapter (See “Joining ThinkEssentials® to existing Networks”, page 22).

NOTE: Please see the User Manual or Instruction Manual for the specific Z-Wave®module being programmed to locate the PROGRAM button and for specific programming information. To add a new controller as a secondary controller to the network, please see the section “Adding a Controller to the Network” page 24.

TIP: If the Z-Wave®module fails to be included in the network it may have previously been used in another network and needs to be reset. Press the REMOVE DEVICE button in ThinkEssentials® and then press and release the PROGRAM button on the Z-Wave®module.

NOTE: The process of adding modules to a network is often referred to as INCLUSION.

Continued next page...



Press ADD DEVICE to add a Z-Wave®module.

Press-and-Release		O	F
Press-and-Release		O	F
		N/
			O
	M		F
	M
PROGRAM button on	I
PROGRAM button on		D
		/.
		G
		O
		RP

module

Device added successfully message window.

Installation/Setup

8

Image 8

Contents Package Contents USB Z-Wave Adapter USB Stand Software on CD Home Control BasicsTable of Contents Basics Copy See ReplicateBasics Number below corresponds to the bubble number above Basics 143Screen Layout Information Installation/Setup Install USB Adapter and USB stand into computer USB portNext Use Change Location link to set your physical locationAdding Modules to the Network Press ADD Device to add a Z-WavemoduleHide Pane Button or Design tab to reveal the icon Operation Common Operations Drawing Floor Plan Button in the Design pane. ThisAgain ErasePress Remove Device to remove a Z-Wavemodule Right-click and select Remove Broken Device Remove/Replace Broken ModulesTo remove the module from Use the following procedure to lock/unlock ThinkEssentials Locked mode the softwareOperations Locking/Unlocking ThinkEssentialsScenes/Zones To include modules into this scene Modifying Scenes/Zones Remove Zone option respectivelySchedules Select Scene/Zone and Action desired  ActivatedLink Modify the desired fields per Instructions in the sectionPages ItemsNetwork Operations Joining ThinkEssentials to Existing NetworksInitiate Primary Controller to Send Replication ExamplePrimary Controller Press ADD Device to add a secondary controller Adding a Controller To the networkSecondary Controller Device removed successfully message window Updating Secondary Controllers Polling Advanced OperationsOptimize/Repair Network Transfer Primary Role From Thinkessentials Initiate Transfer in ThinkEssentialsExample Portable Controller Confirmation of successful transferOn Settings tab, select Switch to or Join Controller Shift commandTransfer Primary Role To Thinkessentials CONTROLLER, or Controller ShiftBackup Network Settings ConfigurationRestore command Click the Backup or Restore Network Settings linkBackup file Wayne-Dalton USB Z-WaveLocated. Note The default parent directory is Command line windowSection on the Settings tab Before you begin, you must ExitModify the Target , then click on APPLY, then OK Adding Command Line Option to ThinkEssentials ShortcutStart ThinkEssentials using the ThinkEssentials icon Command Line Option Multiple Z-WaveUSB Adapters Initiate command line functionType in the /multi command line option ThinkEssentials /multiInitiate command line function Shortcuts Press F5 to refresh and poll the networkExiting/Closing Factory Reset Resetting ThinkessentialsTo reset the USB Z-Wave Adapter Again On the Settings tab, click on the Reset linkTroubleshooting It is enabled on the desired days of week If the modules’s icon is covered by a redThen select the module again Some modules do not supportSet up your network again Check to make sure that there is powerSwitched on Controller to my network. Now, neitherCompliance US and Foreign Patents pending