Wayne-Dalton WDSF-10, WDUSB-10R manual Basics, Copy See Replicate

Page 3

GLOSSARY

Copy – See Replicate.

Delete – Erase transmitter or scene information from Controller. Also known as Exclude. Device – Any item that is connected to a module (for example, lamps).

Exclude – Remove a module, transmitter or scene from the controller. Include – Add a module to the controller. Also known as Inclusion.

Module – Any HomeSettings or Z-Wave®product that is controlled with a HomeSettings or Z-Wave®remote controller. A module can be part of more than one scene.

Network – A collection of Z-Wave®modules controlled by primary and secondary controllers operating on the same system. A network has its own unique identification code so that no one else can control the system.

Node – Single Z-Wave®endpoint (controller or module) on a network . Operator – Garage door opener or garage door operator.

Primary Controller – The first controller used to set up your modules and network.

NOTE: Only the Primary Controller can be used to include or delete modules from a network. It is recommended that you mark the primary controller for each network for ease in modifying your network.

Replicate – Copy from one controller to another.

Scene – A scene is a series of Z-Wave®modules programmed to turn to a specific level (on, off or dim) with the push of a button on a controller.

Schedule - A timer based event in the software that will activate a scene or turn on/off a zone at a specified time of day, or at sunrise or sunset.

Secondary Controller – A controller containing network information about other modules within the network, and is created FROM the primary controller. Secondary controllers cannot include or delete modules to the network.

Sunrise/Sunset Function -- Allows the software to follow sunrise or sunset times. ThinkEssentials® will automatically adjust schedules as daylight length increases or decreases, without the need to be reprogrammed.

Zone - Zones can include one or more modules in your network, allowing them to be turned on or off when pressed or based on a schedule. Also known as groups.

Safety Precautions

This software is intended to be used in normal household circumstances and is expressly not for use in applications where health or safety are dependent on the accurate and timely functioning of the software or in circumstances where a malfunction or error could result in the loss of valuable property.

You should not use this software in conjunction with wireless devices or with items connected to or powered by wireless devices which are not designed for unattended operation.

Basics

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Home Control Basics Package Contents USB Z-Wave Adapter USB Stand Software on CDTable of Contents Copy See Replicate BasicsBasics Basics 143 Screen Layout InformationNumber below corresponds to the bubble number above Install USB Adapter and USB stand into computer USB port Installation/SetupUse Change Location link to set your physical location NextPress ADD Device to add a Z-Wavemodule Adding Modules to the NetworkHide Pane Button or Design tab to reveal the icon Operation Common Operations Erase Drawing Floor PlanButton in the Design pane. This AgainPress Remove Device to remove a Z-Wavemodule Remove/Replace Broken Modules To remove the module fromRight-click and select Remove Broken Device Locking/Unlocking ThinkEssentials Use the following procedure to lock/unlock ThinkEssentialsLocked mode the software OperationsScenes/Zones To include modules into this scene Remove Zone option respectively Modifying Scenes/ZonesSelect Scene/Zone and Action desired SchedulesActivated  Items LinkModify the desired fields per Instructions in the section PagesJoining ThinkEssentials to Existing Networks Network OperationsExample Primary ControllerInitiate Primary Controller to Send Replication Adding a Controller To the network Secondary ControllerPress ADD Device to add a secondary controller Device removed successfully message window Updating Secondary Controllers Advanced Operations Optimize/Repair NetworkPolling Confirmation of successful transfer Transfer Primary Role From ThinkessentialsInitiate Transfer in ThinkEssentials Example Portable ControllerCONTROLLER, or Controller Shift On Settings tab, select Switch to or JoinController Shift command Transfer Primary Role To ThinkessentialsConfiguration Backup Network SettingsWayne-Dalton USB Z-Wave Restore commandClick the Backup or Restore Network Settings link Backup fileBefore you begin, you must Exit Located. Note The default parent directory isCommand line window Section on the Settings tabAdding Command Line Option to ThinkEssentials Shortcut Start ThinkEssentials using the ThinkEssentials iconModify the Target , then click on APPLY, then OK ThinkEssentials /multi Command Line Option Multiple Z-WaveUSB AdaptersInitiate command line function Type in the /multi command line optionInitiate command line function Press F5 to refresh and poll the network ShortcutsExiting/Closing Again On the Settings tab, click on the Reset link Factory ResetResetting Thinkessentials To reset the USB Z-Wave AdapterTroubleshooting Some modules do not support It is enabled on the desired days of weekIf the modules’s icon is covered by a red Then select the module againController to my network. Now, neither Set up your network againCheck to make sure that there is power Switched onUS and Foreign Patents pending Compliance
Top Page Image Contents