Multi-Tech Systems MT3410ZLX When Using V.42bis or MNP5, Some Features Are Disabled, Connect

Page 44

MultiMobile Owner’s Manual

When Using V.42bis or MNP5, Some Features Are Disabled

C: You may be using a non-streaming protocol, like Xmodem or Ymodem to transfer files. Those are fine unless you are using V.42bis or MNP5

S: When using V.42bis or MNP5, you should use a streaming transfer protocol like Ymodem-G or Zmodem.

S: Configure your software to use hardware flow control (RTS/CTS ON).

When Connecting to Another Modem, the Modem Reports a Higher Connect Baud Rate than it Is Really Using

C: The modem defaults to report the modem-to- computer baud rate when it responds with

CONNECT.

S: Go to Command mode with your communication program (like Telix) and type ATW2, then press Enter. This tells the modem to report the modem-to-modem baud rate instead.

When I Run CARDEN, “PC-Card Is Not Enabled Successfully” Is Displayed

C: Your computer does not have enough memory to map the attribute memory of your MT3410ZLX.

S: If memory management software (e.g., EMM386) is installed, you must reserve an area in upper memory (C000:0 — EFFF:F) for MT3410ZLX attribute memory when enabling the card.

44

Image 44
Contents Models MT3410ZLX MT3410ZLX-T/2 MultiMobileTM Model # MT3410ZLX & MT3410ZLX-T/2 Record of RevisionsContents Troubleshooting Comprehensive Driver NotesService Appendix a Technical Specifications Appendix B AT Commands Registers & Result CodesIntroduction and Description About This Manual About This ProductSpecifications Fax FeaturesModem Characteristics Ship Kit Contents System RequirementsIntroduction and Description Installation Safety Warnings Installing The MT3410ZLX or MT3410ZLX-T/2 Cards Menu Installation Driver Software InstallationNovell NetWare Installation Driver Installation Screen Manual Driver Installation Carden Novell Client Installation VLM Microsoft LAN Manager Installation Microsoft LAN Manager Installation Screen Packet Driver Installation Select the Enhanced mode NDIS3 for.... string and press OK Select the Real mode NDIS2 for... string and press OK NDIS2 Driver for WorkgroupODI Driver for Workgroups Select the Netware ODI Driver ... string and press OK Windows NT 3.51 / NT 4.0 Installation Windows 95 Installation Driver from disk provided by hardware manufacturerArtisoft Lantastic 6.0 Installation Factory Default Settings PC Card Software Manual InstallationComprehensive Driver Notes Introduction Quick StartVendor Device Loaded in CONFIG.SYS Using DOS Extended Memory Managers Getting StartedDriver Directory Structure CARDEN.EXEDriver Upgrades Example of partial AUTOEXEC.BAT file LM28NDS2NIF Drivername LM28NDS$ \WFW311\NETSTART Troubleshooting Introduction No Response to AT CommandsModem Does Not Execute the Command Line Modem Goes Off-Hook and Disables the Telephone LineModem Does Not Auto-Answer the Phone Characters on the Screen Are DoubledCommunications Software Dials, but Fails No Text Appears on the Screen in Data ModeNo Text Appears on the Screen When in Command Mode Modem Loses the Connection When in Use Modem Connects with Some Modems, but Not OthersModem Does Not Connect with Another Modem Occasionally, the Modem Gives a Burst of ErrorsModem Gets Random Errors in Transmitted Data Text on the Screen Is Not Legible When Using V.42bis or MNP5, Some Features Are Disabled ConnectExample Device=C\DOS\EMM386.EXE RAM X=D000-D3FF Enabling The MT3410ZLXSelect Use Plug and Play Installing The Win 95 Driver Over SystemSoft CardWorksSelect Properties Select Drivers in Properties COM Port and IRQ Conflicts WindowsWindows Service Limited WarrantyOn-line Warranty Registration Software User License AgreementService Tech Support Recording Modem InformationService How to Use the Multi-Tech BBS About the Multi-Tech BBSAbout CompuServe/Internet About the Multi-Tech Fax-Back System Data Operating SystemsPhysical Appendix B AT Commands Registers & Result Codes Introduction How To Use AT CommandsAT&K3H0Enter Basic AT CommandsCommand Options Function & Description Select Bell 212A for 1200 bps Command Options Function & Description Result code disabled AT& Ampersand Commands Set flow control Grant request from remote for RDL AT% Percent Commands AT\ Back Slash CommandsCommand Options Function & Description =0 or Connect AT- Dash Commands Registers ATSn=x Appendices Page Appendices S62 DTE rate status. The factory default is Appendices Result Codes 333 Carrier Consumer Instructions Page Appendices Page FCC Fax Update Canadian Limitations NoticePage AT Commands, S-Registers Dash Commands Data Specifications Desired DCE speed Installation Installing The MT3410ZLX or PC Card Software Manual Installation Service