Multi-Tech Systems MT2834ZPX owner manual Registers, Escape Code Character

Page 40

MT2834ZPX Owner's Manual

S-Registers

Certain Command Mode configurations are stored in memory registers called, S-Registers. The S command is used to assign a value to, and to read the current value of an S-Register. To assign a value to an S- Register, enter the letter S, followed by the S-Register number and an equals sign (=). To read an S-Register value, enter the letter S followed by the S-Register number and a question mark (?), then hit RETURN. To verify that the S-Register value was entered correctly, enter for example, ATS8? and hit RETURN. You should receive a response of the assigned value given to that S-Register.

S0

Number of Rings Until Modem Answers

Unit:

1 ring

Range:

0-255

Default:

0

Description: Sets the number of rings before the modem answers.

S1

Rings Which Have Occurred

Unit: 1 ring Range: 0-255 Default: 0

Description: Counts the number of rings that have occurred.

S2

Escape Code Character

Unit: ASCII Character

Range: 0-127

Default: 43 (+ sign)

Description: Defines the escape code character.

40

Image 40
Contents Page Record of Revisions Revision Description Contents Index Introduction and Description Modem Features Fax Features Product DescriptionHow to Use This Manual Installation and ConnectionSoftware Configuration AT Commands and S-RegistersService, Warranty & Technical Support/ BBS Testing Your ModemAppendices Installation and Configuration Safety WarningsConfiguration/Installation Procedure Configuration and Installation Procedure StepProcedureInstallation and Configuration Is Your MT2834ZPX Ready for Use? Operating Your MT2834ZPX Simple Operations Software Configuration Introduction Configuring Software for Your ModemPC Initialization Strings AT &F X4 S0= 2 MChanging Default Parameters Configuring Software for Your ComputerConfiguring Software for the Remote System Terminal EmulationFile Transfer Protocols When to Disable Data CompressionAT &F S0=0 X4 &E14 M 16550 Uart and Windows Disabling Error CorrectionAT &F S0=0 X4 &E0 M COMnFIFO=1 COM2FIFO=1Page Modem AT Commands Command a Default $BA0 Description Command Values Default $EB0 Description =0 thru $Fn Command Values Default Command Values Default Description Default &P1 Description RFn Command T = 0, 1, 2, or Values Default Description Command @ Remote Configuration Procedures Remote ConfigurationRemote Configuration Operation Procedures StepProcedure Password Commands Contd. Remote Configuration Operation ProceduresRegisters Escape Code CharacterReturn Character Pause Time for Comma S13 Remote Configuration Escape Character S29 Local Inactivity Timer S36 Time Between DTR Inactive and Modem Off-Hook Result Codes Q0 Multi-Tech Result CodesQ1 Standard AT Result Codes AT Commands and S-Register Summary Troubleshooting Modem Does Not Respond to CommandsPage Modem Dials But Cannot Make a Connection Page Modem Disconnects While Online File Transfer Is Slower Than It Should Be Modem Cannot Connect When AnsweringLosing Data Getting Garbage Characters on the Monitor Fax and Communications Software Won’t Run at the Same TimeTesting Your Modem Local Analog Loopback Test/V.54 Loop Local Analog Loopback TestDigital Loopback Test/V.54 Loop 2 Local/Manual Digital Loopback Test/V.54 Loop 2 Remote/ Automatic Digital Loopback Test local/manualDigital Loopback Test remote/automatic Service, Warranty and Tech Support Introduction Limited WarrantyTech Support On-line Warranty RegistrationRecording Modem Information Service About the Multi-Tech BBS To log on to the Multi-Tech BBSTo Download a file If you know the file nameIf you don’t know the file name About the Multi-Tech Fax-Back Service About CompuServe/InternetAppendix a Technical Specifications Intelligent Features Command BufferModulation Fax ModulationsCarrier Frequencies BpsBell Standard Carrier FrequenciesDataCarrier Frequencies Connectors DiagnosticsTemperature Power Consumption DimensionsAppendix B Tone Dial Frequencies 697 770 852 941 1209 Digits 1336 1477 1633Appendix C FCC and Canadian Regulations RJ11C or RJ11W single line Appendix C FCC and Canadian Regulations Canadian Limitations Notice Index 15, 19 In-band Escape Sequence MultiExpress for Windows PBX/CBX Disconnect Drop Time for DSR/CTS/CD Rings Which Have Occurred Registers Serial port 17, 20, 21 17, 19