Multi-Tech Systems MT5600BA-V92 manual Force Full Startup Procedure Next Connection, Result Code

Page 18

 

 

Chapter 2 – AT Commands

Command:

-QCPC

Force Full Startup Procedure Next Connection

Description:

 

This command causes the modem to use full startup procedures on the next connection

 

 

attempt regardless of the setting of the +PQC command. After this attempt, the modem

 

 

will select the startup procedure as defined by the +PQC command. If a shortened

 

 

startup procedure is enabled by +PQC, then the quick connect profile will also be

 

 

updated on the next connection attempt.

 

 

Syntax: -QCPC

Result Code:

 

OK

 

 

ERROR Otherwise

Command:

-QCPS

Enable Quick Connect Profile Save

Description:

 

This command controls whether or not the modem will save the generated quick

 

 

connect profile.

 

 

Syntax: -QCPS=<value>

Values:

 

0, 1

 

 

<value> Decimal number corresponding to the desired operation.

 

 

0 Do not allow the quick connect profile to be saved.

 

 

1 Allow the quick connect profile to be saved. Default

Result Codes:

 

OK 0 or 1 in V.92 Mode (+MS=V.92) and quick connect is enabled (+PSS = 0)

 

 

ERROR Otherwise

Report Commands:

-QCPS? Reports selected value

 

 

-QCPS=? Reports supported range of parameter values

Multi-Tech Systems, Inc. AT Commands Reference Guide (S000273G)

18

Image 18
Contents MultiModem→ Record of Revisions WarrantyCopyright TrademarksTable of Contents You must press Enter to send the command to the modem IntroductionAT Commands General CommandsCommand Hook Control Command DS=n Dial Stored Telephone NumberCommand En Echo Command Mode Characters Command Information RequestCommand Tone Dialing Command Result Codes Enable/DisableCommand ? Read Register Value Command Result Code FormatCommand Data Carrier Detect DCD Control Command Long Space DisconnectCommand Modem Reset Command Dn Data Terminal Ready DTR ControlCommand Load Factory Settings Command Modem-Initiated Flow ControlCommand V.42bis Data Compression Command V.22bis Guard Tone ControlCommand Clear to Send CTS Control Command Make/Break Dial RatioCommand Sync/Async Mode Command Data Set Ready DSR ControlCommand Select Profile for Hard Reset Command Store Current ConfigurationCommand &Xn Synchronous Clock Source Command &Zn=x Store Telephone NumberCommand Line Signal Quality Command %En Line Quality MonitorCommand Line Signal Level Command PCM Code SelectionCommand \Vn Single Line Connect Message Command \Kn Break ControlCommand \Nn Error Correction Mode Selection Report CommandsValues & Default Country/Region of InstallationCommand +MS= Modulation Selection SubparametersCommand View Numbers in Blacklist Command MNP Extended ServicesCommand Flash Memory Download Command View Delayed NumbersEscape Commands Command +++ Escape SequenceCommand *E Escape Remote Configuration Command +PIG=n PCM Upstream Ignore Modem Connection CommandsCommand +PCW=n Call Waiting Enable Command +PQC=n Quick Connect ControlForce Full Startup Procedure Next Connection Enable Quick Connect Profile SaveResult Code Caller ID Commands Callback Security CommandsCommand +DS Data Compression Data Compression CommandsCommand +DR Data Compression Reporting Command +DS44 V.44 Compression SelectCommand +EFCS Bit Frame Check Sequence Error Control CommandsCommand +EB Break Handling in Error Control Operation Command +ER Error Control ReportingCommand +ESR Selective Reject Command +ETBM Call Termination Buffer Management+ESR? Command +ILRR DTE-Modem Local Rate Reporting DTE CommandsCommand +IFC DTE-Modem Local Flow Control Reported RateCommand +MR Modulation Reporting Control Modulation CommandCommand +IPR Fixed DTE Rate +MCR Report SyntaxBehavior in Data Mode +FCLASS=0 Call Control CommandCommand -STE= Set Telephony Extension Behavior in Voice Mode +FCLASS=8Examples Test Command Command &T n Test CommandNo Carrier ATS86? Configuration Commands Voice CommandsVoice Commands Overview Command +FCLASS=8 Select Voice ModeCommand +VNH= Automatic Hang-up Control Command +FLO Flow ControlCommand +VRX Start Modem Receive Record Voice CommandsCommand +VIP Voice Initialize All Parameters Command +VTS Send Voice TonesCommand +VGT Voice Gain Transmit Playback Volume Command +VTX Start Modem Transmit PlaybackCommand +VGR Voice Gain Receive Record Gain +VTS ExamplesCommand +VIT Voice Inactivity Timer DTE/Modem Command +VLS Analog Source/Destination Selection+VLS Example +VSP=1 Command +VRA Ringback Goes Away TimerTable of +VLS Command Options Label Primitives Description IntervalCommand +VRN Ringback Never Appeared Timer Command +VSD Silence Detection Quiet and SilenceCommand +VSM Compression Method Selection Command +VDT Control Tone Cadence Reporting Command +VTD Beep Tone Duration TimerCommand +VDR Distinctive Ring Before using it DescriptionRate +VPR?Command +VGM Microphone Gain Speakerphone CommandsCommand +VSP Speakerphone ON/OFF Command +VGS Speaker GainVoice Mode Shielded Codes Unformatted Form Reporting Caller IDShielded Hex Event Report Description Code Event Number 4 Extended Keypad Dtmf a Command +A8I CI Signal Indication V.8bis CommandsCommand +A8E V.8bis Operation Controls Default Values25bis Commands List Identification Number 25bis ResponsesList Request of Forbidden Number List Request of Stored NumberReg Unit Range Default Description RegistersRegisters Registers +MR, +ER,+DR, and W commands Result Codes FAX Data+ER None +DR ALT+DR None +ER LapmTerse Verbose Description Terse Verbose Description Setting Country/Regional Codes ExampleIndex Qcpc 46, 47, 48, 49 Index
Related manuals
Manual 57 pages 24.51 Kb

MT5600BA-V92 specifications

Multi-Tech Systems MT5600BA-V92 is a versatile communication device designed for efficient data transmission over telephone lines. It is highly regarded for its reliability and performance in various applications, including point-of-sale transactions, remote monitoring, and data acquisition. One of the key features of the MT5600BA-V92 is its ability to operate at data rates of up to 56 Kbps. This high-speed modem ensures rapid data transfer, making it suitable for businesses that require quick and efficient communication.

The device supports V.92 technology, which enhances the performance of dial-up connections. V.92 provides features like cheaper call setup times, reduced latency, and improved upload speeds compared to older standards. This makes the MT5600BA-V92 an ideal choice for users who need enhanced data performance without investing in more complex networking infrastructure.

Another significant characteristic of the MT5600BA-V92 is its analog communication capabilities. The modem utilizes standard analog telephone lines for connectivity, allowing easy integration into existing telephony systems. This compatibility ensures that businesses can leverage their current infrastructure without needing substantial upgrades.

The MT5600BA-V92 integrates several features for improved functionality, including error correction and data compression technologies. These features enhance the reliability of data transmission by ensuring that lost or corrupted data packets are retransmitted, while compression reduces the amount of data sent over the line, further optimizing performance.

The modem is designed with user-friendliness in mind; it features a straightforward installation process and an intuitive configuration interface. Furthermore, it is compact and robust, making it suitable for diverse environments ranging from retail outlets to industrial applications.

The MT5600BA-V92 is also known for its durability and long life cycle, which is crucial for businesses that rely on continuous operations. Additionally, its ability to operate effectively in various conditions solidifies its position as a dependable communication solution.

In summary, the Multi-Tech Systems MT5600BA-V92 is an advanced modem that combines high-speed data transmission, analog compatibility, and robust error correction features. Its reliable performance and user-friendly design make it an excellent choice for businesses looking to enhance their communication capabilities while utilizing existing telephone infrastructure.