Multi-Tech Systems MT5600BA-V92 manual Index

Index

Index

3

32-bit Frame Check Sequence – +EFCS 21

A

Analog Source/Destination Selection – +VLS	32
Answer – A	5
AT Commands
#CBNn – Store Callback Number	19
#CBPn – Store Callback Password	19
#DBn – Callback Enable/Disable	19
$Cn – Key Abort	15
$Dn – DTR Dialing	15
$SBn – Serial Port Baud Rate	15
%Cn – Data Compression Control	11
%En – Line Quality Monitor	12
%L – Line Signal Level	12
%Q – Line Signal Quality	12
%U – PCM Code Selection	12
&Cn – Data Carrier Detect (DCD) Control	8
&Dn – Data Terminal Ready (DTR) Control	8
&En – Modem-Initiated Flow Control	9
&En – V.42 Error Correction Modes	8
&En – V.42bis Data Compression	9
&Fn – Load Factory Settings	9
&Gn – V.22bis Guard Tone Control	9
&Kn – Flow Control Selection	9
&Mn – Communications Mode	9
&Pn – Make/Break Dial Ratio	10
&Qn – Sync/Async Mode	10
&Rn – Clear to Send (CTS) Control	10
&Sn – Data Set Ready (DSR) Control	10
&Tn – Local Analog Loopback Test	10
&Tn – V.54 Test Command	27
&Vn – Display Current Configuration and Statistics
for Last Connection	10
&Wn – Store Current Configuration	11
&Xn – Synchronous Clock Source	11
&Yn – Select Profile for Hard Reset	11
&Z3 – Leased-Line Dial Back-up Number Storage
	11
&Zn – Store Telephone Number	11
** – Flash Memory Download	15
*B – View Numbers in Blacklist	15
*D – View Delayed Numbers	15
*E – Escape Remote Configuration	16
+++ – Escape Sequence	16
+A8E – V.8 and V.8bis Operation Controls	40
+A8I – CI Signal Indication	40
+DR – Data Compression Reporting	20
+DS – Data Compression	20
+DS44 – V.44 Compression Select	20
+EB – Break Handling in Error Control Operation 21
+EFCS – 32-bit Frame Check Sequence	21
+ER – Error Control Reporting	21
+ESR – Selective Reject	22
+ETBM – Call Termination Buffer Management	22
+FCLASS= – Set Current Fax Class	13

+FCLASS=8 – Select Voice Mode	28
+FLO – Flow Control	29
+GCI – Country/Region of Installation	14
+IFC – DTE-Modem Local Flow Control	23
+ILRR – DTE-Modem Local Rate Reporting	23
+IPR – Fixed DTE Rate	24
+MR – Modulation Reporting Control	24
+MS= – Modulation Selection	14
+PCW=n – Call Waiting Enable	17
+PIG=n – PCM Upstream Ignore	17
+PQC=n – Quick Connect Control	17
+PSS – Use Short Sequence	17
+VCID=n – Caller ID Selection	19
+VDR – Distinctive Ring	35
+VDT – Control Tone Cadence Reporting	35
+VGM – Microphone Gain	37
+VGR – Voice Gain Receive (Record Gain)	31
+VGS – Speaker Gain	37
+VGT – Voice Gain Transmit (Playback Volume) 31
+VIP – Voice Initialize All Parameters	30
+VIT – Voice Inactivity Timer (DTE/Modem)	32
+VLS – Analog Source/Destination Selection	32
+VNH – Automatic Hang-up Control	29
+VPR – Select DTE/Modem Interface Rate (Turn
Off Autobaud)	36
+VRA – Ringback Goes Away Timer	33
+VRID= – Caller ID Report Retrieved	19
+VRN – Ringback Never Appeared Timer	34
+VRX – Start Modem Receive	30
+VSD – Silence Detection (Quiet and Silence)	34
+VSM – Compression Method Selection	34
+VSP – Speakerphone ON/OFF	37
+VTD – Beep Tone Duration Timer	35
+VTS – Send Voice Tone(s)	30
+VTX – Start Modem Transmit (Playback)	31
A – Answer code	5
A/ – Repeat Last Command	5
\An – Maximum MNP Block Size	12
AT – Attention code	5
Bn – Communication Standard Setting	5
\Bn – Transmit Break	12
CIC – Connect Incoming Call	41
CRIs – Call Request Identification	41
CRNs – Call Request Number	41
CRSx – Call Request Address	41
DIC – Disregard Incoming Call	41
Ds – Dial	5
DS=n – Dial Stored Telephone Number	6
En – Echo Command Mode Characters	6
Hn – Hook Control	6
In – Information Request	6
\Kn – Break Control	13
-Kn – MNP Extended Services	15
L5 – Lists Current Operating Parameters	6
Mn – Monitor Speaker Mode	6
\Nn – Error Correction Mode Selection	13
On – Return Online to Data Mode	6
P – Pulse Dialing	6

Multi-Tech Systems, Inc. AT Commands Reference Guide (S000273G) 52