Multi-Tech Systems MT5600BA-V92 manual 46, 47, 48, 49

Index

Local Analog Loopback Test – &Tn	10
Long Space Disconnect – Yn	8

M

Make/Break Dial Ratio – &Pn	10
Maximum MNP Block Size – \An	12
Microphone Gain – +VGM	37
MNP Extended Services – -Kn	15
Modem Connection Commands
+PCW=n – Call Waiting Enable	17
+PIG=n – PCM Upstream Ignore	17
+PQC=n – Quick Connect Control	17
+PSS – Use Short Sequence	17
-QCPC – Force Full Startup Procedure Next
Connection	18
-QCPS – Enable Quick Connect Profile Save	18
Modem Reset – Zn	8
Modem-Initiated Flow Control – &En	9
Modulation Command
+MR – Modulation Reporting Control	24
Modulation Reporting Control – +MR	24
Modulation Selection – +MS=	14
Monitor Speaker Mode – Mn	6

O

Online command mode 4

P

PCM Code Selection – %U	12
PCM Upstream Ignore – +PIG=n	17
press Enter	4
Pulse Dialing – P	6

Q

Quick Connect Control – +PQC=n 17

R

Read Register Value – Sr?		7
Repeat Last Command – A/		5
Result Code Format – Vn		7
Result Code Selection – Xn		7
Result Codes Enable/Disable – Qn		7
results codes	46, 47, 48, 49, 50
Return Online to Data Mode – On		6
Ringback Goes Away Timer – +VRA		33
Ringback Never Appeared Timer – +VRN		34

S

Program Identification Number – PRIa	41
Program Number – PRNx	41
Select DTE/Modem Interface Rate (Turn Off
Autobaud) – +VPR	36
Select Profile for Hard Reset – &Yn	11
Select Register – Sr	7
Select Voice Mode – +FCLASS=8	28
Selective Reject – +ESR	22
Send Voice Tone(s) – +VTS	30
Serial Port Baud Rate – $SBn	15
Set Current Fax Class – +FCLASS=	13
Set Register Value – Sr=n	7
Set Telephony Extension – -STE=	25
Silence Detection (Quiet and Silence) – +VSD	34
Single Line Connect Message – \Vn	13
Speaker Gain – +VGS	37
Speakerphone Commands
+VGM – Microphone Gain	37
+VGS – Speaker Gain	37
+VSP – Speakerphone ON/OFF	37

Speakerphone ON/OFF – +VSP	37
S-Registers	43
Start Modem Receive – +VRX	30
Start Modem Transmit (Playback) – +VTX	31
Store Callback Number – #CBNn	19
Store Callback Password – #CBPn	19
Store Current Configuration – &Wn	11
Store Telephone Number – &Zn	11
Sync/Async Mode – &Qn	10
Synchronous Clock Source – &Xn	11

T

Test Command
&Tn – V.54 Test Command	27
Tone Dialing – T	7
Transmit Break – \Bn	12

U

Unformatted Form Reporting – Caller ID	38
Use Short Sequence – +PSS	17

V

V.22bis Guard Tone Control – &Gn	9
V.25bis Commands
CIC – Connect Incoming Call	41
CRIs – Call Request Identification	41
CRNs – Call Request Number	41
CRSx – Call Request Address	41
DIC – Disregard Incoming Call	41
RLD – List Request of Delayed Call Number	41
RLF – List Request of Forbidden Number	42
RLI – List Identification Number	42
RLN – List Request of Stored Number	42
PRIa	41
PRNx	41
V.42 Error Correction Modes – &En	8
V.42bis Data Compression – &En	9
V.44 Compression Select – +DS44	20
V.54 Test Command – &Tn	27
V.8 / V.8bis Commands
+A8E – V.8 and V.8bis Operation Controls	40
+A8I – CI Signal Indication	40
V.8 and V.8bis Operation Controls – +A8E	40
VAL – V.25bis Response	42
View Delayed Numbers – *D	15
View Numbers in Blacklist – *B	15
Voice Commands
+VDR– Distinctive Ring	35
+VDT– Control Tone Cadence Reporting	35
+VGR – Voice Gain Receive (Record Gain)	31
+VGT – Voice Gain Transmit (Playback Volume) 31
+VIP – Voice Initialize All Parameters	30
+VIT – Voice Inactivity Timer (DTE/Modem)	32
+VLS – Analog Source/Destination Selection	32
+VPR – Select DTE/Modem Interface Rate (Turn
Off Autobaud)	36
+VRA – Ringback Goes Away Timer	33
+VRN – Ringback Never Appeared Timer	34
+VRX – Start Modem Receive	30
+VSD – Silence Detection (Quiet and Silence)	34
+VSM – Compression Method Selection	34
+VTD – Beep Tone Duration Timer	35
+VTS – Send Voice Tone(s)	30
+VTX – Start Modem Transmit (Playback)	31
Voice Configuration Commands
+FCLASS=8 – Select Voice Mode	28
+FLO – Flow Control	29
+VNH – Automatic Hang-up Control	29

Multi-Tech Systems, Inc. AT Commands Reference Guide (S000273G) 54