N-Tron 102PC-SE user manual Scenario 4 Serial Tunneling Mode, # set ip telnet raw-mode enable

Page 35

Scenario 4 – Serial Tunneling Mode

This scenario shows a serial tunnel established between two serial devices (Serial Device-1, Serial Device-2) using two 102PC-SEs, which are geographically located apart.

	Serial Tunneling
Commands for Module-1	Commands for Module-2
(Configure for Serial Auto Dial-in).	(Configure for Telnet Auto Dial-out)
# set ip eth0 dhcp-client disable
# set ip eth0 ip-address 192.168.2.1	# set ip eth0 dhcp-client disable
# set ip telnet raw-mode enable	# set ip eth0 ip-address 192.168.2.10
# set serial auto-dialin enable	# set ip auto-dialout enable
# set serial s0 raw-dialin enable	# set ip telnet raw-mode enable
# set serial s0 auto-dialin enable	# set serial s0 auto-dialout enable
# set serial s0 auto-dialin trig-mode none	# set serial s0 auto-dialout-port 5000
# set serial s0 auto-dialin-ipaddress 192.168.2.10	# set serial s0 auto-dialout-protocol telnet
# set serial s0 auto-dialin-port 23	# set serial s0 raw-dialout enable
# set serial s0 auto-dialin-protocol telnet	# set serial s0 baud-rate 115200
# set serial s0 baud-rate 115200	# set serial s0 data-bits 8
# set serial s0 data-bits 8	# set serial s0 parity none
# set serial s0 parity none	# set serial s0 stop-bits 1
# set serial s0 stop-bits 1	# set serial s0 flow-control rts-cts
# set serial s0 flow-control rts-cts	# save
# save

12/1/2006

35

Image 35

Contents 12/1/2006 Table of Contents 12/1/2006 Contact Information Safety WarningsEnvironmental Safety Electrical Safety Unpacking Package ContentsCleaning DIN Rail Mounting ServicingColor Description Front PanelApplying Power Top View Grounding Techniques Connecting the Unit RS-232 Serial InterfaceSerial Cable Support FCC Statement TroubleshootingCLI Tree of Menus Set Set configurable fields Serial Configure the serial settings for the serial port s0 Recv-mail Configure incoming mail optionsSend-mail Configure outgoing mail options Show Show general and detailed information Socket Actions to take over a UDP socket Web Management Software Configuration12/1/2006 Web Management Tree of Menus General ConfigurationUser Configuration Port ConfigurationChatscript Modem ConfigurationBridge Configuration PPP ConfigurationSuccessfully. These cannot be modified Telnet ConfigurationAutodial Configuration UDP ConfigurationPOP3 Configuration Http ConfigurationSnmp Configuration Smtp Address ConfigurationSntp General Sntp Daylight Saving ConfigurationCommands Restore DefaultsEthernet to Serial Connectivity Mandatory Configuration SettingsScenario 1 Manual Dialout Commands to Setup Manual Dial-out with the 102PC-SEPrerequisites Scenario 2 Auto Dialout Using TelnetAuto Dialout Feature using UDP Mode Scenario 3 Auto Dialout Using UDPScenario 4 Remote Bridging with Modem Connection # set ppp ppp0 raw-mode enableSerial to Ethernet Connectivity Scenario 1 Manual Serial Dial-in Commands to Setup Manual Dial-In with the 102PC-SEScenario 2 Serial Auto Dial-in Using Telnet Functionality Scenario 3 Serial Auto Dial-in Using UDP# set serial s0 raw-dialout enable Scenario 4 Serial Tunneling Mode# set ip telnet raw-mode enable Using E-Mail Features Sending Text E-mails from the Command Prompt Receiving E-mails from the Command Prompt Physical KEY SpecificationsSwitch Properties Emissions and Safety ApprovalsTron Limited Warranty