N-Tron 102PC-SE user manual Ethernet to Serial Connectivity, Mandatory Configuration Settings

Page 26

Ethernet to Serial Connectivity

Mandatory Configuration Settings

The following items must be configured in order to use the manual dial-out feature:

∙Disable the Host Interaction Mode to restrict Telnet-Dial-Out and PPP.

#set serial <s0> host-interaction-mode disable

∙Disable Auto dial-out globally on all the serial ports.

#set ip auto-dialout disable

∙Disable Auto dial-out on the serial port s0.

#set serial s0 auto-dialout disable

The following items must be configured in order to use the auto dial-out feature:

∙Disable the Host Interaction Mode to restrict Telnet-Dial-Out and PPP.

#set serial <s0> host-interaction-mode disable

∙Enable Auto dial-out globally on all the serial ports.

#set ip auto-dialout enable

∙Enable Auto dial-out on the serial port s0.

#set serial s0 auto-dialout enable

∙Set the Auto dialout port for the serial port s0 .

#set serial s0 auto-dialout-port <port_number>

∙Set the Auto dialout protocol for the serial port s0.

#set serial s0 auto-dialout-protocol <telnet or udp>/all

An ERROR message will display if any of the above details are not configured or are not valid.

Optional Configuration Settings

The following details are optional configurations:

∙Enable/Disable the Authentication for Dial-out session

#set login auto-dialout-login <enable/disable>

∙Enable/Disable the Switching-between-Dialout & CommandPrompt feature

#set ip telnet escape-monitor <enable/disable>

∙Set the Escape-Monitor-String to switch between Dialout and Command Prompt sessions.

#set ip telnet escape-string "+++inet"

∙Enable/Disable the Terminating Dialout Session using Terminate string

#set ip udp terminate-monitor <enable/disable>

∙Set the Terminate-Monitor-String to Terminate the Dialout Session.

#set ip udp terminate-string "+++inet"

∙Enable/Disable the Terminating Dialout Session using Inactivity Timeout

#set ip udp inactivity <enable/disable>

∙Set the Inactivity Timeout to Terminate the Dialout Session.

#set ip udp inactivity-timeout 300

∙Enable/Disable the Raw mode globally for all Dial-out sessions.

#set ip telnet raw-mode <enable/disable>

∙Enable/Disable the Raw mode for the serial port s0.

#set serial s0 raw-dialout <enable/disable>

∙Set the Baud rate for the serial port s0 to be taken for a Dialout session.

#set serial s0 baud-rate <Baud-rate>

∙Set the Flow control for the serial port s0 to be taken for a Dialout session.

#set serial s0 flow-control <rts-cts/none>

∙Set the Parity for the serial port s0 to be taken for a Dialout session.

#set serial s0 parity <even/odd/none>

∙Set the Data bits for the serial port s0 to be taken for a Dialout session.

#set serial s0 data-bits <7/8>

∙Set the Stop bits for the serial port s0 to be taken for a Dialout session.

#set serial s0 stop-bits <1/1.5/2>

12/1/2006

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents 12/1/2006 Table of Contents 12/1/2006 Safety Warnings Contact InformationEnvironmental Safety Electrical Safety Unpacking Package ContentsCleaning Servicing DIN Rail MountingFront Panel Color DescriptionApplying Power Top View Grounding Techniques Connecting the Unit RS-232 Serial InterfaceSerial Cable Troubleshooting Support FCC StatementCLI Tree of Menus Set Set configurable fields Serial Configure the serial settings for the serial port s0 Recv-mail Configure incoming mail optionsSend-mail Configure outgoing mail options Show Show general and detailed information Socket Actions to take over a UDP socket Software Configuration Web Management12/1/2006 Port Configuration General ConfigurationUser Configuration Web Management Tree of MenusPPP Configuration Modem ConfigurationBridge Configuration ChatscriptTelnet Configuration Successfully. These cannot be modifiedUDP Configuration Autodial ConfigurationSmtp Address Configuration Http ConfigurationSnmp Configuration POP3 ConfigurationRestore Defaults Sntp Daylight Saving ConfigurationCommands Sntp GeneralMandatory Configuration Settings Ethernet to Serial ConnectivityCommands to Setup Manual Dial-out with the 102PC-SE Scenario 1 Manual DialoutScenario 2 Auto Dialout Using Telnet PrerequisitesScenario 3 Auto Dialout Using UDP Auto Dialout Feature using UDP Mode# set ppp ppp0 raw-mode enable Scenario 4 Remote Bridging with Modem ConnectionSerial to Ethernet Connectivity Commands to Setup Manual Dial-In with the 102PC-SE Scenario 1 Manual Serial Dial-inScenario 2 Serial Auto Dial-in Using Telnet Scenario 3 Serial Auto Dial-in Using UDP Functionality# set serial s0 raw-dialout enable Scenario 4 Serial Tunneling Mode# set ip telnet raw-mode enable Using E-Mail Features Sending Text E-mails from the Command Prompt Receiving E-mails from the Command Prompt Emissions and Safety Approvals KEY SpecificationsSwitch Properties PhysicalTron Limited Warranty
Top Page Image Contents