MaxTech V.32bis, V.42bis user manual Basic Response Codes

Page 15

BASIC RESPONSE CODES

OK	0	CONNECT	1
RING	2	NO CARRIER	3
ERROR	4	CONNECT 1200	5
NO DIALTONE	6	BUSY	7
NO ANSWER	8	CONNECT 2400	10
CONNECT 4800	11	CONNECT 7200	12
DATA	13	CONNECT 9600	14
FAX	15	CONNECT 12000	16
CONNECT 14400	17	+FCERROR	+F4

MODIFIED RESPONSE CODES (\V1)

CONNECT 300/REL	22	CONNECT 1200/REL	24
CONNECT 2400/REL	25	CONNECT 4800/REL	26
CONNECT 7200/REL	27	CONNECT 9600/REL	28
CONNECT 12000/REL 29		CONNECT 14400/REL	30

EXTENDED RESPONSE CODES (\V2)

CONNECT 300/REL-MNP	32
CONNECT 1200/REL-MNP	34
CONNECT 2400/REL-MNP	35
CONNECT 4800/REL-MNP	36
CONNECT 7200/REL-MNP	37
CONNECT 9600/REL-MNP	38
CONNECT 12000/REL-MNP	39
CONNECT 14400/REL-MNP	40
CONNECT 300/REL-MNP 5	42
CONNECT 1200/REL-MNP 5	44
CONNECT 2400/REL-MNP 5	45
CONNECT 4800/REL-MNP 5	46
CONNECT 7200/REL-MNP 5	47
CONNECT 9600/REL-MNP 5	48
CONNECT 12000/REL-MNP 5	49
CONNECT 14400/REL-MNP 5	50
CONNECT 1200/REL-LAPM	54
CONNECT 2400/REL-LAPM	55
CONNECT 4800/REL-LAPM	56
CONNECT 7200/REL-LAPM	57
CONNECT 9600/REL-LAPM	58
CONNECT 12000/REL-LAPM	59
CONNECT 14400/REL-LAPM	60
CONNECT 1200/REL-LAPM V.42BIS	64
CONNECT 2400/REL-LAPM V.42BIS	65
CONNECT 4800/REL-LAPM V.42BIS	66
CONNECT 7200/REL-LAPM V.42BIS	67

14

Image 15

Contents Contents Unpacking Your Modem Hardware InstallationFasten the retaining bracket Software Installation/ConfigurationPage Devices in your computer cannot share an IRQ with COM Port and Interrupt SettingsUsing Your Modem Testing Your Modem After InstallationWhere To Go From Here Executing CommandsCommand Structure Basic AT Commands Extended AT Commands Enable Trellis Coding @ Mode after DTR toggleGuard tone disabled Force DSR Signal High onDisable Auto Fall Forward/Back 22bis auto-retrain disabled22bis auto-retrain enabled Enable Auto Fall Forward/BackFax Class 1 Commands Voice Mode Commands S Registers Function Range/units Default Basic Response Codes Modem does not respond to commands Modem does not dialModem dials but does not connect Modem makes a connection but no data appears on your screen High pitch tone is heard whenever you answer the phoneModem exhibits poor voice record or playback Uart FCC ComplianceDOC Compliance Information FCC Class B StatementDisclaimer, Copyright, And Other Notices Section One Introduction Software Installation/Configuration COM Port and Interrupt Settings Switch Block SW-1 Location Switch Block Settings Testing Your Modem After Installation With AT or follow with Enter Bold text Command Function Manually answer incoming callCcitt mode Originate calls in answer modeCommands are not echoed Hz guard tone Resets modem after DTR toggleRecall factory default configuration Toggle\A3 MNP/V.42/V.42bis Commands\Q3 Switch to reliable link from normal link S Registers Register Function Range/units DefaultSection Five Result Codes Section Six Troubleshooting Modem does not dial Power 75 W Section Eight Support and Service DOC Compliance Information Disclaimer, Copyright, And Other Notices