Liebert RAC2-8 manual Set Modem Options

Page 28

Section 3: Operation

Set Modem Options

Press 7 from the Main Menu to display the Set Modem Options screen.

RAC2-8 MAIN MENU

 

 

 

 

 

** SET MODEM OPTIONS **

 

 

 

1.

Phone Number

=

 

 

 

 

2.

Site ID

=

 

 

 

 

3.

Dial Prefix

=

ATE1X4DT

 

 

4.

Redial Interval (minutes)

= 01

 

5.

Redial Tries (--- = Forever)

= 03

6.

Modem Messages

Y/N

= No

 

 

<ESC> TO EXIT

 

 

 

 

 

Phone Number = 7944

 

 

 

 

** SET MODEM OPTIONS **

 

 

 

1.

Phone Number

=

7944

 

 

 

2.

Site ID

=

 

 

 

 

3.

Dial Prefix

=

ATE1X4DT

 

 

4.

Redial Interval (minutes)

= 01

 

S. Redial Tries (--- = Forever)

= 03

6.

Modem Messages

Y/N

= No

 

 

<ESC> TO EXIT

 

 

 

 

 

Site ID

=

AIR ROOM #1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

These parameters are unique to terminal operation.

The Site ID (up to 20 characters) is user selected to identify a specific facility. The Dial Prefix activates the modem and therefore must be compatible with the modem. The Dial Prefix is factory set. Do not change the Dial Prefix without consulting the modem user’s manual. Modem messages describe modem activity such as No Answer, Line Busy, Redial in 3 Minutes, etc. Select Yes if you want these messages displayed at the terminal.

Make modem baud rate selection by setting DIP Switch 2-1 inside the RAC2-8 enclosure. Refer to Figure 5–4 in SECTION 5 — INSTALLATION. Set Switch 2-2 to ON (down) if you are using a leased line.

The Modem must be Hayes or Hayes compatible. Switches inside the modem should remain factory set except the following which are user selectable.

Liebert RAC2-8 23

Image 28
Contents $XWRð&KDQJHRYHUý&RQWUROOHU Table of Contents Table of Figures RAC2-8 UnitPage Introduction Page To start up the RAC2-8 InstallationOperation Page Operation Glossary of Control Functions for more detailsSequencing Status Screens cont’d Status Sub-menuDelay UnitsSet Options Sub-menu Status Sub-menu cont’dSet Options Sub-menu cont’d Function Delays TEMP/HUM Password StandbyAlarm Sub-menu Set Clock Sub-menu DateTime DAY of WeekUnit 01 Forced on Force OFF Restore Return Terminal LOG onStatus Screen Setup Zones/Units Options Setup Zones/Units Options cont’dNumber of ZONES/NUMBER of Units PER Zone Unit StatusUnit Shutdown on Alarm Emergency Power Units08 0 no Unit Labels Alarms Review and Alarms ClearSet Clock Override a Unit Set Modem Options Setup Temp/Humid Options cont’d Setup Temp/Humid OptionsSet Modem Options cont’d Setup Standby Unit Options Display SS Alarm Block Set New PasswordAlarms List of AlarmsAlarm Annunciation Alarm CommunicationsAlarm Delay AutochangeoverAutosequencing Clear Alarms Common Alarm-InputsCommon Alarm-Output KeyDelay Emergency Power OFF EPOEmergency Power Operation Hold DelayHumidity Alarms Humidity LockoutInactive Unit IntervalNormal Temperature PasswordPower Failure Mode OverrideRestart Delay RestoreStandby Testing Running UnitsTemperature Alarms Temperature SensitivityTemperature Staging TerminalZones Installation TB2 RAC2-8 Dimensional Enclosure Diagram RAC2-8 Component Arrangement RAC2-8 Connection Diagram RAC2-8 Switch and Jumper Settings