Lantronix 900-332 manual Contents

Page 5

Contents

Copyright and Trademark _________________________________________________ i

Contacts ______________________________________________________________ i

Disclaimer and Revisions _________________________________________________ ii

1: Using This Guide

1-1

Purpose and Audience _________________________________________________ 1-1

Chapter Summary _____________________________________________________ 1-1

Additional Documentation _______________________________________________ 1-2

2: Introduction

2-1

Capabilities __________________________________________________________ 2-1

Applications __________________________________________________________ 2-2

Protocol Support ______________________________________________________ 2-2

Configuration Methods _________________________________________________ 2-2

Addresses and Port Numbers ____________________________________________ 2-3

Hardware Address _________________________________________________________ 2-3

IP Address________________________________________________________________ 2-3

Port Numbers _____________________________________________________________ 2-3

3: Configuration using DeviceInstaller

3-1

Accessing WiPort using DeviceInstaller ____________________________________ 3-1

Server Configuration ___________________________________________________ 3-1

WLAN Configuration ___________________________________________________ 3-2

Host List Configuration _________________________________________________ 3-3

OEM Pin Configuration _________________________________________________ 3-3

Channel 1 and Channel 2 Configuration ____________________________________ 3-4

Email Configuration ____________________________________________________ 3-8

4: Configuration using Web-Manager

4-1

Accessing WiPort using Web-Manager _____________________________________ 4-1

Network Configuration __________________________________________________ 4-2

Automatic IP Address Configuration ____________________________________________ 4-3

Static IP Address Configuration _______________________________________________ 4-3

Server Configuration ___________________________________________________ 4-4

Host List Configuration _________________________________________________ 4-5

Channel 1 and Channel 2 Configuration ____________________________________ 4-6

Serial Settings _____________________________________________________________ 4-6

Connection Settings - TCP ___________________________________________________ 4-8

Connection Settings - UDP __________________________________________________ 4-11

Email Configuration ___________________________________________________ 4-12

Trigger Configuration ______________________________________________________ 4-13

WLAN Configuration __________________________________________________ 4-14

OEM Pin Configuration ________________________________________________ 4-16

Updating Settings ____________________________________________________ 4-17

WiPort™ User Guide

iii

Page 4 Page 6
Image 5
Page 4 Page 6
Contents WiPort User Guide Page Sales Offices Lantronix Corporate HeadquartersTechnical Support Disclaimer and Revisions Contents Accessing Setup Mode ContentsWlan Settings5-19 Expert Settings5-20Exit Configuration Mode Factory DefaultsGpio Pins Control ProtocolPage Purpose and Audience Using This GuideChapter Summary Remaining chapters in this guide includeAdditional Documentation Using This GuideCapabilities IntroductionApplications Configuration MethodsProtocol Support IntroductionHardware Address Addresses and Port NumbersIP Address Port NumbersPage Server Configuration Configuration using DeviceInstallerAccessing WiPort using DeviceInstaller Wlan Configuration Configuration Using DeviceInstaller Host List ConfigurationOEM Pin Configuration Channel 1 and Channel 2 Configuration Serial Settings Common I/F Mode SettingUDP Datagram Mode Passive ConnectionActive Connection Buffer Flushing DisconnectionConnection Packing Email ConfigurationUnit Name TriggersPage Accessing WiPort using Web-Manager Configuration using Web-ManagerConfiguration Using Web-Manager Network ConfigurationStatic IP Address Configuration Automatic IP Address ConfigurationClick the OK button when finished Select Obtain IP address automaticallyDefault Gateway Select Use the following IP configurationIP Address Subnet MaskAdvanced Server ConfigurationHost Information Serial SettingsRetry Settings Disable Serial Port Port SettingsAvailable fields, enter the following information ChannelPack Control Connection Settings TCPFlush Input Buffer Serial to Network Flush Output Buffer Network to SerialConnect Protocol Connect Mode Passive ConnectionConnect Mode Active Connection Common Options Endpoint ConfigurationDisconnect Mode Datagram Mode Connection Settings UDPMail Server IP Address Configure the following fieldsChange Address Table Enable Serial Trigger Configurable PinsRecipients ConditionsMessage Properties Enter or modify the following fields Ad Hoc SettingsWireless Network Security Configure or modify the following fields for each pin Advanced SettingsUpdating Settings Page Telnet Access Configuration via Serial Mode or Telnet PortAccessing Setup Mode Click OK. The following information displays Serial Port AccessConfiguration Via Serial Mode or Telnet Port Set the Gateway IP Address Set the IP AddressSet the Netmask Change Telnet Configuration PasswordDhcp Name Network Class Host Bits NetmaskFollowing table displays available I/F Mode options Interface ModeMode Option Interface Mode OptionsFlow Common I/F Mode Setting Binary HexPort Number Flow Control OptionEnter Connect Mode options in hexadecimal notation Connect ModeConnect Mode Option Port Numbers Reserved forResponse Incoming ConnectionAutostart Automatic Connection Manual ConnectionManual Connection Address Example Hostlist Example HostlistMessage Meaning Modem ModeDatagram Type Function Modem Mode CommandModem Mode Commands Remote Port Modem Mode Function CommandRemote IP Address Disconnect Mode Option Flush Mode10. Disconnect Mode Options 11. Flush Mode OptionsOption Channel Port Password DisConnTime Inactivity TimeoutSendChar 1 and SendChar2 Telnet Terminal TypeMail Server Domain Name Unit NameRecipient TriggerEnable Wlan Wlan SettingsEnable Ad Hoc Network Creation Find Network NameSecurity Settings Expert SettingsDisable Telnet Setup Disable SnmpDisable Tftp Firmware Upgrade Disable Port 77FE HexFactory Defaults Wlan Settings Channel 1 ConfigurationChannel 2 Configuration Expert Settings Exit Configuration ModeSecurity Settings Email SettingsGpio Pins Configurable PinsFeatures Control ProtocolConfigurable Pins CommandsByte 0 Command Types Command 10h, Get FunctionsCommand 12h, Get Active Levels Command 11h, Get DirectionsCommand 13h, Get Current States Command 19h, Set DirectionsCommand 1Bh, Set States Command 1Ah, Set Active LevelsCommand details Examples1Bh = response to command 1Bh 03h, 00h, 00h, 00h = Page Entering Monitor Mode via the Serial Port Monitor ModeEntering Monitor Mode via the Network Port To enter Monitor Mode locallyFollowing commands are available in Monitor Mode Monitor Mode CommandsCommand Command Name Function Monitoring the NetworkUpdating Firmware Using Tftp Graphical User InterfaceObtaining Firmware Reloading Firmware ROM File FWX FileTroubleshooting Using Tftp Command Line InterfaceRecovering the Firmware Using the Serial Port Problem/Message Reason Solution TroubleshootingProblems and Error Messages Caps Lock is not on Please try againDevice Server message General DeviceInstaller SettingsTechnical Support Europe, Middle East, and Africa Technical Support
Top Page Image Contents