Lantronix 900-332 Entering Monitor Mode via the Serial Port, To enter Monitor Mode locally

Page 73

7: Monitor Mode

Monitor Mode is a command-line interface used for diagnostic purposes.

This chapter includes the following topics:

Topic	Page
Entering Monitor Mode via the Serial Port	7-1

Entering Monitor Mode via the Network Port	7-1

Monitor Mode Commands	7-2

There are two ways to enter Monitor Mode: locally via the serial port or remotely via the network.

Entering Monitor Mode via the Serial Port

To enter Monitor Mode locally:

1.Follow the same steps used for setting the serial configuration parameters (see Serial Port Access on page 5-2).

2.Instead of typing three x keys, however:

a)Type zzz to enter Monitor Mode with network connections.

b)Type yyy to enter Monitor Mode without network connections.

A 0> prompt indicates that you have successfully entered Monitor Mode.

Entering Monitor Mode via the Network Port

To enter Monitor Mode using a Telnet connection:

1.Establish a Telnet session to the configuration port (9999). The following message appears:

MAC address 00204A0113A3

Software version 05.3 (040129) WPT

Press Enter to go into Setup Mode

2. Type M (upper case).

A 0> prompt indicates that you have successfully entered Monitor Mode.

WiPort™ User Guide

7-1

Image 73

Contents WiPort User Guide Page Technical Support Lantronix Corporate HeadquartersSales Offices Disclaimer and Revisions Contents Accessing Setup Mode ContentsWlan Settings5-19 Expert Settings5-20Exit Configuration Mode Factory DefaultsGpio Pins Control ProtocolPage Purpose and Audience Using This GuideChapter Summary Remaining chapters in this guide includeAdditional Documentation Using This GuideCapabilities IntroductionApplications Configuration MethodsProtocol Support IntroductionHardware Address Addresses and Port NumbersIP Address Port NumbersPage Accessing WiPort using DeviceInstaller Configuration using DeviceInstallerServer Configuration Wlan Configuration OEM Pin Configuration Host List ConfigurationConfiguration Using DeviceInstaller Channel 1 and Channel 2 Configuration Serial Settings Common I/F Mode SettingUDP Datagram Mode Passive ConnectionActive Connection Connection DisconnectionBuffer Flushing Packing Email ConfigurationUnit Name TriggersPage Accessing WiPort using Web-Manager Configuration using Web-ManagerConfiguration Using Web-Manager Network ConfigurationStatic IP Address Configuration Automatic IP Address ConfigurationClick the OK button when finished Select Obtain IP address automaticallyDefault Gateway Select Use the following IP configurationIP Address Subnet MaskAdvanced Server ConfigurationRetry Settings Serial SettingsHost Information Disable Serial Port Port SettingsAvailable fields, enter the following information ChannelPack Control Connection Settings TCPFlush Input Buffer Serial to Network Flush Output Buffer Network to SerialConnect Mode Active Connection Connect Mode Passive ConnectionConnect Protocol Disconnect Mode Endpoint ConfigurationCommon Options Datagram Mode Connection Settings UDPChange Address Table Configure the following fieldsMail Server IP Address Enable Serial Trigger Configurable PinsRecipients ConditionsMessage Properties Wireless Network Security Ad Hoc SettingsEnter or modify the following fields Configure or modify the following fields for each pin Advanced SettingsUpdating Settings Page Accessing Setup Mode Configuration via Serial Mode or Telnet PortTelnet Access Configuration Via Serial Mode or Telnet Port Serial Port AccessClick OK. The following information displays Set the Gateway IP Address Set the IP AddressSet the Netmask Change Telnet Configuration PasswordDhcp Name Network Class Host Bits NetmaskFollowing table displays available I/F Mode options Interface ModeMode Option Interface Mode OptionsFlow Common I/F Mode Setting Binary HexPort Number Flow Control OptionEnter Connect Mode options in hexadecimal notation Connect ModeConnect Mode Option Port Numbers Reserved forResponse Incoming ConnectionManual Connection Address Example Manual ConnectionAutostart Automatic Connection Hostlist Example HostlistDatagram Type Modem ModeMessage Meaning Modem Mode Commands Modem Mode CommandFunction Remote IP Address Modem Mode Function CommandRemote Port Disconnect Mode Option Flush Mode10. Disconnect Mode Options 11. Flush Mode OptionsOption Channel Port Password DisConnTime Inactivity TimeoutSendChar 1 and SendChar2 Telnet Terminal TypeMail Server Domain Name Unit NameRecipient TriggerEnable Wlan Wlan SettingsEnable Ad Hoc Network Creation Find Network NameSecurity Settings Expert SettingsDisable Telnet Setup Disable SnmpDisable Tftp Firmware Upgrade Disable Port 77FE HexFactory Defaults Channel 2 Configuration Channel 1 ConfigurationWlan Settings Expert Settings Exit Configuration ModeSecurity Settings Email SettingsGpio Pins Configurable PinsFeatures Control ProtocolConfigurable Pins CommandsByte 0 Command Types Command 10h, Get FunctionsCommand 12h, Get Active Levels Command 11h, Get DirectionsCommand 13h, Get Current States Command 19h, Set DirectionsCommand 1Bh, Set States Command 1Ah, Set Active LevelsCommand details Examples1Bh = response to command 1Bh 03h, 00h, 00h, 00h = Page Entering Monitor Mode via the Serial Port Monitor ModeEntering Monitor Mode via the Network Port To enter Monitor Mode locallyFollowing commands are available in Monitor Mode Monitor Mode CommandsCommand Command Name Function Monitoring the NetworkUpdating Firmware Using Tftp Graphical User InterfaceObtaining Firmware Reloading Firmware ROM File FWX FileRecovering the Firmware Using the Serial Port Using Tftp Command Line InterfaceTroubleshooting Problems and Error Messages TroubleshootingProblem/Message Reason Solution Caps Lock is not on Please try againDevice Server message General DeviceInstaller SettingsTechnical Support Europe, Middle East, and Africa Technical Support